毕业论文论文范文课程设计实践报告法律论文英语论文教学论文医学论文农学论文艺术论文行政论文管理论文计算机安全
您现在的位置: 毕业论文 >> 论文 >> 正文

基于WINCC组态软件对复杂工程设计的研究与实现+WINCC界面设计

更新时间:2011-12-29:  来源:毕业论文

Based on WINCC configuration software to complex engineering design's research and realization Abstract
Along with industrial automation level rapid enhancement, the people were getting higher and higher to industrial automation's request, integrated the man-machine contact surface (HMI) the system and the monitoring management (SCADA) system's general industrial automation configuration software's appearance, has realized the perfect process visualization, provided the complete operation and the surveillance function for each industrial field.
This article mainly said that 论文网http://www.751com.cn/  (1)uses Siemens's WinCC 6.2 configuration software design manufacture friendly man-machine contact surface, and/operates kneading board + one, two cording diagrams with the touchscreen/text monitor to constitute the tertiary monitoring new pattern together, realizes the use superior machine and tracks the record as well as to equipment's common control in the papermaking process to each technical process system's real-time monitoring;(2) And the use industry ethernet switchboard and the ordinary ether network card connect PLC and industry PC machine through the TCP/IP way small scale, enables the entire worn out papermaking production system to be possible systematically the networking. Solves between each Production department not to be able prompt, quick, the convenience relation question, the change “to play singles the aspect which since long fights alone, uses in realizing raises the entire papermaking system's production efficiency, the movement reliability, convenience production management, the reduced nonessential manpower waste even environmental protection.  Key words:Networking  Triple Monitor  HMI  WinCC
目  录本文来自辣,文,论,文·网原文请找腾讯QQ3249,114
摘  要 I
Abstract II
1引言 1
1.1项目研究的背景 1
1.2项目研究的内容 3
2工艺流程 3
2.1制浆 3
2.2调制 4
2.3抄造 5
2.4污水处理 6
3系统组成及其联网 8
3.1系统硬件组成 8
3.1.1 CPU315-2DP/CPU414-2DP 9
3.1.2机架(rack) 10
3.1.3ET-200M 10
3.1.4交换机 11
3.1.5上位机 12
3.2系统网络组成 12
3.2.1以太网 12
3.2.2多模光纤 13
3.2.3PPI通讯协议 14
3.2.4MPI通讯协议 14
3.2.5CP5611卡 15
3.2.6RS232 15
3.2.7RS485 16
3.2.8PROFIBUS – DP 16
3.3系统整体联网 18
4WINCC界面设计 23
4.1添加变量和设计制作界面 24
4.2界面的组成 28
4.2.1工艺流程示意图 29
4.2.2菜单的切换 30
4.2.3弹出式控制窗口 31
4.2.4报警画面 31
4.2.5趋势图画面 32
4.2.6参数表/棒图 36
4.2.7登陆界面和用户权限 36
4.3各种监控设备的相互配合 38
4.4WINCC运行 43
5系统运行结果、分析、总结与展望 44
5.1系统运行结果与分析 44
5.2项目总结与展望 45
参考文献 46
附  录 48
谢  辞 49,2273

[1] [2] [3] [4] [5] [6] 下一页

基于WINCC组态软件对复杂工程设计的研究与实现+WINCC界面设计下载如图片无法显示或论文不完整,请联系qq752018766
设为首页 | 联系站长 | 友情链接 | 网站地图 |

copyright©751com.cn 辣文论文网 严禁转载
如果本毕业论文网损害了您的利益或者侵犯了您的权利,请及时联系,我们一定会及时改正。