毕业论文

打赏
当前位置: 毕业论文 > 电子通信 >

基于ATE通用平台的测试适配器的硬件设计

时间:2018-04-19 21:10来源:毕业论文
针对某雷达的故障检测介绍了一款基于ATE平台的测试适配器的设计,以完善ATE平台的功能。这款测试适配器以AT91SAM9G20 ARM芯片和Stratix ® III系列FPGA为主处理器

摘要随着科技的飞速发展,电子设备的应用越来越广泛,当电子设备中的电路板一旦发生故障,将会使得电子设备的使用造成严重影响。传统的电路板故障检测诊断技术效率低、花费高,而且需要经验丰富的工作人员才能完成。为了改善这一现状,人们设计了ATE平台,但是ATE平台并不能完全满足电路板故障检测诊断的全部需求,本文针对某雷达的故障检测介绍了一款基于ATE平台的测试适配器的设计,以完善ATE平台的功能。这款测试适配器以AT91SAM9G20 ARM芯片和Stratix ® III系列FPGA为主处理器,辅以FLASH、SSRAM、DRAM、DAC、ADC电路完成整个适配器的工作。完成了硬件原理图和PCB的设计,加工装配后进行了系统测试,测试结果表明本测试适配器达到设计要求。21444
关键词  电路板  故障检测诊断技术  ATE平台  ARM  FPGA  PCB
 毕业论文设计说明书(论文)外文摘要
Title  Hardware design of test adapter based on ATE platform                                           
Abstract
With the rapid development of science and technology, more and more extensive application of electronic equipment, when once the circuit board of the electronic equipment failure, it will make the use of electronic equipment caused serious influence. Low traditional circuit board fault detection and diagnosis of technical efficiency , high cost , and require experienced staff to complete. In order to improve this situation, people design the ATE platform, but the ATE platform does not fully meet all the needs of detecting circuit board fault diagnosis.So this paper describes a test adapter,which based on ATE platform to improve the function of ATE platform and this test adapter is designed for a radar fault detection. This test adapter with AT91SAM9G20 ARM chip and the Stratix ® III series FPGA as the main processor ,and  with FLASH, SSRAM, DRAM, DAC, ADC circuit to complete the adapter work.After designing the hardware schematic diagram and PCB, processing and assembling,we conduct the system testing. Finally the test results show that the test adapter to meet the design requirements.
Keywords    Circuit board,Fault detection and diagnosis techniques,   ATE platforms,ARM,FPGA,PCB
目    录
1.绪论    1
1.1  研究背景    1
1.2  国内外研究现状    1
1.3  本文内容及章节安排    3
2  适配器总体设计和元器件选择    4
2.1  测试适配器总体设计    4
2.2    主处理器ARM的选择    5
3  适配器硬件电路设计    10
3.1  ARM系统电路    10
3.1.1  电源电路    10
3.1.2    存储电路    12
3.2  FPGA系统电路    15
3.2.1  电源电路    15
3.2.2  数据存储电路    19
3.2.3  AD转换电路    20
3.2.4  DA转换电路    23
3.3  PCB设计    24
3.7.1 PCB的设计流程    24
3.7.2本课题的 PCB设计    25
4  系统测试    27
4.1测试方案    27
4.2测试过程    27
4.2.1网口测试    27
4.2.2串口测试    28
4.3测试结果    29
结  论    31 基于ATE通用平台的测试适配器的硬件设计:http://www.751com.cn/tongxin/lunwen_13649.html
------分隔线----------------------------
推荐内容