▼B 

4. SPECIFICATIONS  

4.1.  Definitions (see ►M4  Annex II   ◄) 

▼M2

4.1.1.  H is a reference poi nt as defined in Item 1.1 of Annex III to Directive 77/649/EEC   which  must  be  determined   in  accordance   with  the procedure set out in that Directive. 

4.1.1.1. Point H′  is the reference point corresponding to H as defined in Item 

4.1.1 and  shall  be determined  for  all  normal  positions in  which  the 

seat is used. 

4.1.1.2.  Point R is the seat reference  point defined in Item 1.2 of Annex III to 

Directive 77/649/EEC. 

4.1.2.  The reference line is a straight line as def ined in Item 3.4 of Annex 

III to Directive 77/649/EEC.  

▼B

4.1.3. Points L1 and L2 are the lower effective belt anchorages. 

▼M2 

4.1.4.  Point  C  is  the  point  situated  450  mm  vertically  above  point  R. 

However, if the distance S defined in Item 4.1.6 is not less than 280 mm and if the alternative formula BR = 280 mm + 0·8  S specified in Item  4.4.4.3  is  chosen  by  the  manufacturer,  t he  vertical  distance between C and R shall be 500 mm. 

▼B

4.1.5. The angles α1 and  α2 are respectively the angl es between a horizontal plane  and  planes  perpendicular  to  the  median  longitudinal  plane  of the vehicle and passing through  ►M2   point H′◄ and points L1 and L2.  

4.1.6.  S is the distance in millimetres of the effective upper belt anchorage from a reference plane P parallel to the longitudi nal median plane of the vehicle defined as follows:  

4.1.6.1.  if the  seating  position  is  well  defined  by  the  shape  of the  seat,  the plane P shall be the medi an plane of this seat; 

4.1.6.2.  in the absence of  a well-defined position:  

▼M2

4.1.6.2.1.  the  plane  P  for  the  driver's  seat  is  a  vertical  plane  parallel  to  the median  longitudinal   plane  of the  vehicle  which  passes  through  the centre  of the  steering-wheel  in   the  plane  of the  steering-wheel  rim when the steering-wheel, if adjust able, is in its  central position; 

▼B

4.1.6.2.2.  the  plane  P   for  the  front  outboard  passenger  shall  be  symmetrical with that of the driver; 

4.1.6.2.3.  plane P for the rear outboard seating position shall be that specified by  the  manufacturer   on  condition   t hat  the   following  limits   for distance A between the longitudinal median plane of the vehicle and plane P are respected:  

A  ≥  200 mm ifthe bench seat has been des igned to accomodate two passengers 

only, 

▼M2

A  ≥  300 mm, ifthe bench seat has been designed to accommodate more than two 

passengers. 

▼B 

4.2.  General specifications   一般技术要求 

4.2.1.  Anchorages for a safety belt shall be so designed, made  and situated as to: 

4.2.1.1. enable  the installati on  of a suitable safety belt. The belt anchorages of  the   汽车安全带英文文献和中文翻译(5):http://www.751com.cn/fanyi/lunwen_45011.html