菜单
  
    ABSTRACT: In thermoplastic injection moulding, part quality and cycle time depend strongly on the cooling stage. Numerous strategies have been investigated in order to determine the cooling conditions which minimize undesired defects such as warpage and differential shrinkage. In this paper we propose a methodology for the optimal design of the cooling system. Based on geometrical analysis, the cooling line is defined by using conformal cooling concept. It defines the locations of the cooling channels. We only focus on the distribution and intensity of the fluid temperature along the cooling line which is here fixed. We formulate the determination of this temperature distribution, as the minimization of an objective function composed of two terms. It is shown how this two antagonist terms have to be weighted to make the best compromise. The expected result is an improvement of the part quality in terms of shrinkage
    and warpage.  21511
     
    1  INTRODUCTION 
    In the field of plastic industry, thermoplastic injection
    moulding is widely used. The process is composed of
    four essential stages: mould cavity filling, melt packing,
    solidification of the part and ejection. Around seventy
    per cent of the total time of the process is dedicated to
    the cooling of the part. Moreover this phase impacts
    directly on the quality of the part [1][2]. As a
    consequence, the part must be cooled as uniformly as
    possible so that undesired defects such as sink marks,
    warpage, shrinkage, thermal residual stresses are
    minimized. The most influent parameters to achieve
    these objectives are the cooling time, the number, the
    location and the size of the channels, the temperature of
    the coolant fluid and the heat transfer coefficient
    between the fluid and the inner surface of the channels.
    The cooling system design was primarily based on the
    experience of the designer but the development of new
    rapid prototyping process makes possible to manufacture
    very complex channel shapes what makes this empirical
    former method inadequate. So the design of the cooling
    system must be formulated as an optimization problem.
     
    1.1  HEAT TRANSFER ANALYSIS
    The study of heat transfer conduction in injection tools is
    a non linear problem due to the dependence of
    parameters to the temperature. However thermophysical
    parameters of the mould such as thermal conductivity
    and heat capacity remain constant in the considered
    temperature range. In addition the effect of polymer
    crystallisation is often neglected and thermal contact
    resistance between the mould and the part is considered
    more often as constant.
    The evolution of the temperature field is obtained by
    solving the Fourier’s equation with periodic boundary
    conditions. This evolution can be split in two parts: a
    cyclic part and an average transitory part. The cyclic part
    is often ignored because the depth of thermal penetration
    does not affect significantly the temperature field [3].
    Many authors used an average cyclic analysis which
    simplifies the calculus, but the fluctuations around the
    average can be comprised between 15% and 40% [3].
    The closer of the part the channels are, the higher the
    fluctuations around the average are. Hence in that
    configuration it becomes very important to model the
    transient heat transfer even in stationary periodic state.
    In this study, the periodic transient analysis of
    temperature will be preferred to the average cycle time
    analysis. 
    It should be noticed that in practice the design of the
    cooling system is the last step for the tool design.
    Nevertheless cooling being of primary importance for
    the quality of the part, the thermal design should be one
    of the first stages of the design of the tools.
  1. 上一篇:数字EL定位器英文文献及中文翻译
  2. 下一篇:雷达成像技术对钢筋混凝土桥梁的无损检测英文文献和中文翻译
  1. JSP技术简介及特点英文文献和中文翻译

  2. 模具以及模具的现代加工英文文献和中文翻译

  3. 注塑模具的设计及其热分...

  4. 知识管理及其对隐性知识...

  5. 液压系统英文文献及中文翻译

  6. 机床结构动态性能预测英文文献及中文翻译

  7. JAVA和因特网英文文献及中文翻译

  8. 电站锅炉暖风器设计任务书

  9. 河岸冲刷和泥沙淤积的监测国内外研究现状

  10. 当代大学生慈善意识研究+文献综述

  11. 大众媒体对公共政策制定的影响

  12. java+mysql车辆管理系统的设计+源代码

  13. 十二层带中心支撑钢结构...

  14. 酸性水汽提装置总汽提塔设计+CAD图纸

  15. 乳业同业并购式全产业链...

  16. 杂拟谷盗体内共生菌沃尔...

  17. 中考体育项目与体育教学合理结合的研究

  

About

751论文网手机版...

主页:http://www.751com.cn

关闭返回