菜单
  

    ) and
    maximum 500 mm s
    –1
    injection speed (injection flowrate
    509 cm3
    s
    –1
    ) (Fig. 6, Table 2). The necessary injection
    thrust of the 36 mm screw is 2.
    7 times that of the 22 mm
    screw and the maximum pressure is 300 MPa.
    The servomotor for the ‘S-2000i100B high speed
    injection specification’ was developed with higher torque
    than the servomotor installed on the ‘S-2000i100A high
    6 ROBOSHOT S-2000i100B high speed injection specificationspeed injection specification’. Although the motor outer
    dimension is greater because of the increased rotor size
    for higher power, the average torque is achieved in a
    slow to fast speed range. Furthermore, the increase in
    rotation inertia is reduced to a minimum.
    Because the motor power is so large, if a standard
    drive mechanism using a pulley and belt is used, the
    rotation inertia would be extremely large with the wider
    belt and pulley because of the power transition capacity.
    Therefore, a mechanism with direct connection of the
    servomotor and the ball screw is used in the ‘S-
    2000i100B high speed injection specification’.
    Furthermore, high precision pressure control, not
    influenced by external noise, is achieved by application
    of a high precision and high resolution digital load cell.
    Figure 7 shows the injection acceleration performance
    for light guide panel mouldings using the ‘S-2000i100B
    high speed injection specification’. This machine
    achieves 15 ms of rapid acceleration, which is superior
    to the performance of the ‘S-2000i100A high speed
    injection specification’.
    Figure 8 shows the injection pressure curve in the
    metering process. In this process, the injection servo-
    motor and screw rotation servomotor rotate at the same
    time. It was confirmed that high precision pressure
    control was achieved with ,1 kgf cm–2
    variance.
    Injection unit driven by linear motor
    As mentioned before, to fill thin walled products with
    wall thicknesses less than 0.
    2 mm, injection speeds over
    1000 mm s
    –1
    are required. The maximum available
    injection speed for the injection unit with a combination
    of rotary servomotor and ball screw is around
    800 mm s
    –1
    . However, linear motors are known as a
    means of attaining high speeds, and Fanuc has devel-
    oped and supplied linear motors since 1994.为了以一个精确和稳定的方式生产薄壁制品,FANUC已经开发了电动式注塑机,由旋转或直线电机驱动,以满足产品成型所需特定功能,如很薄的壁厚或特殊形状的塑料材料。在本文中,每种注射单元的必要特征和许多模具的实例一起被介绍。论文网
    关键词:高速,壁薄,伺服电机,直线电机,精度控制
    介绍
    由于信息产业的不断发展,对于小、轻、超精密产品的需求量也在增加。在塑料成型行业,更薄或更高精度的产品继续发展,这一趋势也愈发显著。
    典型的塑料制品包括微小的存储器芯片的把手,或手机或数码相机电池箱。为了生产这样薄的模具制品,模具的一个总的技术组合——材料和注塑机的技术——是必需的。
    尤其对注塑机而言,一个将熔融材料以一个很短的时间高速和高加速度的充满型腔是必需的。
  1. 上一篇:钢筋在混凝土中的受压英文文献和中文翻译
  2. 下一篇:暖通空调系统优化英文文献和中文翻译
  1. 汽车乘员舱的声振耦合英文文献和中文翻译

  2. 立体光照成型的注塑模具...

  3. 低频振动的铁路车轴的状...

  4. 接头的形状对沥青塞接头...

  5. 电-气动驱动的垂直计算机...

  6. 开口端纺纱系统中的锥形...

  7. 木质填料聚丙烯复合材料...

  8. 当代大学生慈善意识研究+文献综述

  9. 电站锅炉暖风器设计任务书

  10. 中考体育项目与体育教学合理结合的研究

  11. 杂拟谷盗体内共生菌沃尔...

  12. 大众媒体对公共政策制定的影响

  13. java+mysql车辆管理系统的设计+源代码

  14. 酸性水汽提装置总汽提塔设计+CAD图纸

  15. 乳业同业并购式全产业链...

  16. 十二层带中心支撑钢结构...

  17. 河岸冲刷和泥沙淤积的监测国内外研究现状

  

About

751论文网手机版...

主页:http://www.751com.cn

关闭返回