菜单
  

    and practically feasible APJ design that mitigates stress and strain
    concentrations under operating thermal and traffic loads. The
    premise of the paper is that improved APJ performance can be
    obtained by minimizing stress and strain demands within the APJ,
    a task achieved through parametric simulations. The parametric
    studies described herein involve four sets of alternative geometric
    parameters as shown in Fig. 2: interface between pavement and
    APJ Set IF, gap plate thickness Set GT, gap plate edge detail
    Set GE, and gap plate width Set GL. Based on the information
    obtained from the parametric studies, an improved APJ design is
    proposed and its superiority over the traditional design is demon-
    strated.
    Finite-Element Model Development, Calibration,
    and Validation
    Two-dimensional, plane strain finite-element models developed
    by Park et al. 2010 are used in the investigation of APJ re-
    sponse. The typical APJ design 500100 mm of widthdepth
    with 20010 mm gap plate suggested by the Bridge Joint As-
    sociation 2003 is used as a prototype. Eight-node isoparametric
    elements are used to mesh the concrete deck, pavements, main
    APJ region, and gap plate as shown in Fig. 3. The developed
    models are run on ABAQUS V6.7.Since the mesh contains corners, the stress level at those loca-
    tions will rise as the element size is decreased. To ensure that
    meaningful results are achieved, the mesh is graded such that the
    element size in critical zones, where cracks are expected to ini-
    tiate, is 1 mm and quantities of interest within each element are
    averaged over the element domain. The chosen 1-mm element
    size is deemed appropriate for representing the processes that lead
    to direct or fatigue crack initiation. This size is similar to that
    used in fracture studies conducted by Kim et al. 2009, albeit
    they used a particle element model rather than a finite element
    model as used herein. As noted in Park et al. 2010, the objective
    of this effort is not to model crack initiation and propagation in
    the APJ material itself, which involve complex phenomena asso-
    ciated with time and temperature dependencies as well as healing
    of asphalt. Rather, the intent is to evaluate stress and strain mea-
    sures that are deemed indicative of the propensity for direct or
    fatigue cracking in the main APJ body.
    To present the results and facilitate comparisons between vari-
    ous configurations in the future, the results of the simulations are
    plotted along the path AFDBCE-ECBDFA shown in Fig. 4.
    Points D and E along with corresponding points E and D
    represent the tips of the debonded interface. Park et al. 2010
    showed that the most critical points are located along this bound-
    ary. Due to symmetry, only one-half of the model is employed in
    thermal movement analysis, whereas, in case of moving traffic
    load, a full model is used because the loading condition is not
    symmetric. The main quantities of interest are maximum principal
    stresses p and strains p and are computed 0.5 mm away
    from the boundary, which coincides with the center of the small-
    est elements at the critical points.
    While APJ material is comprised of aggregate and pure as-
    phalt, the model employed herein assumes that the material is
    homogenous. As a viscous, temperature-dependent material, as-
    phalt exhibits a stiffer and stronger response at high strain rate or
    cold temperatures compared to response under slow strain rates or
    high temperatures. Therefore, the model for the APJ material used
    in this work is a time- and temperature-dependent model, which
    consists of two parallel networks: an elastic-plastic network and
    an elastic-viscous network. The behavior of the elastic-plastic net-
  1. 上一篇:启发式算法热轧机铝英文文献和中文翻译
  2. 下一篇:颚式破碎机外文文献和中文翻译
  1. 接头的形状对沥青塞接头...

  2. 沥青填充式伸缩缝英文文献和中文翻译

  3. 连续大跨度桥梁结构英文文献和中文翻译

  4. 液压缸起重器和柱塞英文文献和中文翻译

  5. 船用柴油发动机的活塞组件英文文献和翻译

  6. 桥梁工程英文文献和中文翻译

  7. 高压活塞水泵英文文献和中文翻译

  8. java+mysql车辆管理系统的设计+源代码

  9. 当代大学生慈善意识研究+文献综述

  10. 乳业同业并购式全产业链...

  11. 电站锅炉暖风器设计任务书

  12. 大众媒体对公共政策制定的影响

  13. 十二层带中心支撑钢结构...

  14. 酸性水汽提装置总汽提塔设计+CAD图纸

  15. 杂拟谷盗体内共生菌沃尔...

  16. 河岸冲刷和泥沙淤积的监测国内外研究现状

  17. 中考体育项目与体育教学合理结合的研究

  

About

751论文网手机版...

主页:http://www.751com.cn

关闭返回