菜单
  

     (1) rapid prototyping and manufacturing (RPM).  It consists of three-dimensional laser lithography (SLA); laminated profile manufacturing (LOM); laser powder sintering prototyping (SLS); Fused Deposition Molding (FDM) and three-dimensional printing forming technology (3D-P) and so on.
     (2) the surface forming tooling.  It refers to the use of spray, chemical corrosion, electroforming and new method for the formation of the cavity surface and a fine pattern technology.
     (3) Casting forming tooling.  There are bismuth tin alloy tooling, zinc alloy tooling, resin composite forming technology and silicon rubber mold molding technology.
     (4) cold extrusion mold technology and ultra-molded shapes.
     (5) multi-point forming technology.
     (6) KEVRON steel blanking blanking tooling.
     (7) mold blank rapid manufacturing technology.  Mainly dry sand Mold Casting, Vacuum Mold Casting, Resin Sand Mold Casting Lost Wax Casting, and other technologies.
     (8) Other aspects of technology.  Such as the use of nitrogen gas spring pressure side, discharge, quick die technology, stamping unit technology, and cutting edge technology and solid surfacing edge inserts die casting technology.
     4.4 mold materials and surface treatment technology developed rapidly
      Industry to the level of mold, material application is the key.  Due to improper selection and use of materials, causing premature die failure, which accounts for more than 45% failure die.  In the mold material, commonly used cold work tool steel with CrWMn, Cr12, Cr12MoV and W6Mo5Cr4V2, flame hardened steel (such as Japan, AUX2, SX105V (7CrSiMnMoV), etc.; used a new type of hot work die steel American H13, Sweden QRO80M, QRO90SUPREME, etc.; used a pre-hardened plastic mold steel  (such as the U.S. P20), age-hardening steel (such as the U.S. P21, Japan NAK55, etc.), heat treatment hardened steel (such as the United States, D2, Japan, PD613, PD555, Sweden wins the White 136, etc.), powder die steel (such as Japan KAD18 and KAS440), etc.; panel drawing die used HT300, QT60-2, Mo-Cr, Mo-V cast iron, large-scale mold with HT250. more regular use of Precision Die Hard Steel Results YG20 and other alloys and carbide. in the mold surface treatment, the main trends are: the infiltration of a single element to the multi-element penetration, complex permeability (such as TD method) development; by the general diffusion to the CVD, PVD, PCVD, ion penetration , the direction of ion implantation, etc.; can use the coating are: TiC, TiN, TiCN, TiAlN, CrN, Cr7C3, W2C, etc., while heat from the air treatment means to the development of vacuum heat treatment. In addition, the current strengthening of the laser, glow plasma Nitriding and electroplating (plating) enhanced anti-corrosion technologies are also more and more attention.
     4.5 mold industry new techniques, new ideas and new models have been gradually recognized
      In the forming process, the main function of composite stamping die, superplastic forming, plastic precision molding technology, plastic mold gas-assisted injection technology and hot runner technology, high-pressure injection molding technology.  On the other hand, with the continuous development of advanced manufacturing technology and raise the level of mold industry as a whole, in the mold industry, there are some new design, production, management ideas and models.  Concrete are: to adapt to the characteristics of mold-piece production flexible manufacturing technologies; to create the best management and effective teamwork, lean production; to enhance rapid response capabilities of Concurrent Engineering, Virtual Manufacturing and global agile manufacturing, manufacturing of new production networks philosophy; extensive use of standard parts common parts of the pision of work mode of production; meet the environmental requirements of sustainable development and green design and manufacturing. Summary
  1. 上一篇:换热器的机械设计英文文献和中文翻译
  2. 下一篇:ASP.NET英文文献和中文翻译
  1. 汽车乘员舱的声振耦合英文文献和中文翻译

  2. 立体光照成型的注塑模具...

  3. 低频振动的铁路车轴的状...

  4. 接头的形状对沥青塞接头...

  5. 电-气动驱动的垂直计算机...

  6. 开口端纺纱系统中的锥形...

  7. CAD/CAM模具技术课程教学改...

  8. 杂拟谷盗体内共生菌沃尔...

  9. 大众媒体对公共政策制定的影响

  10. 河岸冲刷和泥沙淤积的监测国内外研究现状

  11. 当代大学生慈善意识研究+文献综述

  12. 中考体育项目与体育教学合理结合的研究

  13. java+mysql车辆管理系统的设计+源代码

  14. 酸性水汽提装置总汽提塔设计+CAD图纸

  15. 乳业同业并购式全产业链...

  16. 电站锅炉暖风器设计任务书

  17. 十二层带中心支撑钢结构...

  

About

751论文网手机版...

主页:http://www.751com.cn

关闭返回