- 上一篇：预应力混凝土梁英文文献和中文翻译
- 下一篇：模具快速制造技术英文文献和中文翻译
With precisely rubs truncates the law manufacture punching die, specially makes the high accuracy, the high life punching die, such as: Thin material small gap compound punching die, multi- locations continuous type compound die and so on, has the size precision high, the work component smachined surface roughness Ra value is small, the mold life higher characteristic. Its processing craft at present changed the electrical fire by the past ordinary engine bed rough machining spark cutting or the electricity puncher rough machining, finally precisely rubs truncates, also from takes shape rubs, optics curve rubs, the manual grid reference rubs gradually filters the continual path grid reference to rub and NC and the CNC continual path grid reference rubs, Processing coarseness may reach ±0.001 ~ 0.0005mm, the processing surface roughness Ra value may reach 0.1 ~ 0.025 mu m. Therefore, with this craft manufacture the die , regardless of the size precision, the work components surface roughness, all can satisfy die, each kind of compound request, the die is especially higher than the electrical finishing craft manufacture scale.
(4) gap size and degree of homogeneity
the flange and other sheet forming sgene rally all must first punching (fall material) the plate to launch the semi finished materials, after also has the forming to fall the material, the incision obtains the single end product to flush. Therefore punching the work, including is commonly used punching hole, the margin, cut side and so on, regarding each kind of sheet pressing partall is necessary. Therefore punching the gap to flushes a out form in chprecision to have the decisive influence. punching the gap small and is even, may cause punching the size gain high accuracy. Regarding drawability, is curving and so on mould, the gap greatly will decide increases flushes the oral area size error and the snapping back. The gapnon-uniformity can cause to flush a burr enlarges and incurs cutting edge the non-uniform attrition.
(5) ramming equipment elastic deformation In the ramming process
After the punch press load bearing can have the certain elastic deformation. Although this kind of distortion quantity according to flushes the pressure the size to change also to have the obvious directivity, but on the pressing part, mainly is to has the volume ramming archery target stamping, embosses, the equalization, the pressure is raised, the wave, flushes crowds, the shape, the flange, hits flatly, thinly changes draw ability and so on the craft work punching forming flushes, has the significant influence to its ramming aspect size precision
板料冲压件的精度准确显示出其冲模的冲压精度。而任何冲件的线性尺寸精度与形位精度主要取决于冲模冲裁和立体成形冲压件展开平毛坯的落料精度。因此，多工步复合冲压的单工位复合模、多工位连续模的冲压精度，在普通冲压的众多种类与不同结构的冲模中，最具典型性和代表性。论文网
冲模的冲压精度分析
对冲模投产至失效报废各个时期冲件的实际误差分析，可以看出其增大的时期及趋向，从而分析其增大的因素。新冲模投产至第一次刃磨前冲制冲件的误差即所谓的初始误差；冲模经过20次左右刃磨至失效报废前冲制的冲件误差称之为常规误差；而冲模失效报废前冲制的最后一批合格冲件的允许最大误差称之为极限误差。在现场，确定冲模刃磨寿命的依据是冲件冲孔与落料的毛刺高度。由于任何成形件都具有冲裁作业（毛坯落料或冲孔），对于复合模尤为如此。所以，冲件毛刺高度的触模检查和测量并按企业标准或JB4129-85《冲压件毛刺高度》对照检测就显得十分重要。