菜单
  

     At an installation at a U.S. corrugated medium mill, the triple-cone refiner replaced two 34-in. double disc refiners and one Jordan, all of which operated in series on 350 tpd of OCC. Each of the double disc refiners used a 600-hp motor, and the Jordan used a 400-hp motor. Approximately 150 points of CSF drop are taken across the three refiners. The new refiner was connected to one of the existing 600- hp motors. At startup, the new refiner achieved all paper tests alone, while using only 425 gross horsepower. After initial trials, the refiner was able to improve the sheet characteristics, as shown in Table 3. The projected annual energy savings in this installation are approximately $325,000/year. A second triple-cone refiner is now being considered for the mill's second paper machine.

     TABLE 3. Trial data: Conical refiner on corrugating medium

     GRADE

     TEST

     PREVIOUS RESULT AVG.NEW RESULT AVG.

     UNITS 

    26# Medium          CMT 49.08  57.04 Pounds Force

    26# Medium          Ring Crush 31.24 31.92 Pounds Force

    30# Bag              Mullen Burst 16.88 18.96 PSI

    30# Bag              Gurley Porosity 24.24 27.52 sec/100 mL

     OTHER BENEFITS. 

    These results have been repeated now in trials and installations on most types of furnish and grades of paper grades and energy savings is available in the online version of this article in the Extra Edition section of www.paperloop.com

    In general it was found that the triple-cone refiner did not generate the same level of hydrodynamic forces or flow velocities within the refining zones as an equivalent double disc refiner. This improves the residence time of the fiber in the refining zones, which contributes to the overall energy efficiency. Due to the reduced forces and flow velocities, the new conical refiners are somewhat more sensitive to plugging from furnish contaminants. Good screening is essential to longevity of the tackle, especially in the use of recycled fibers.

    The characteristics within the conical refiners improve the flow of the furnish across the bar intersections. The improvement in fibrillation and reduction in fines generation may be the result of more fibers being present at the bar intersections due to this flow characteristic. Lower overall refining intensity also comes into play relative to fibrillation and should be beneficial to the refining of hardwoods and recycled fibers. A secondary result of the improved fiber mat between tackle surfaces is a reduction in metal-to-metal contact and a reduction in the potential of tackle clashing. Both result in improved tackle life when compared with double disc refiners.

    CONCLUDING REMARKS

    Fibre shortening is a predominant effect of refining. A majority (about 60%) of the separated fibrous elements are poorly developed. The PFI refining of long fibre fractions shows a similar influence on fibre characteristics as does the industrial refining. A probable limiting factor might be the nature of wood itself. Removing the outer layers of cell walls without chemical modification does not significantly enhance fibre bonding.

    As we move more fully into the Information Age, success will require that the engineer possess some unique knowledge of and experience in both the development and the management of technology. Success will require broad knowledge and skills as well as expertise in some key technologies and disciplines; it will also require a keen awareness of the social and economic factors at work in the marketplace. Increasingly, in the future, routine problems will be expected to work cooperatively in solving more challenging, more demanding problems in substantially less time. We have begun a new phase in the practice of engineering. It offers great promise and excitement as more and more problem-solving capability is placed in the hands of the computerized and wired engineer. To assure success, the capability of our tools and the unquenched thirst for better products and systems must be matched by the joy of creating that marks all great engineering endeavors. Mechanical engineering is a great profession, and it will become even greater as we make the most of the opportunities offered by Information Age.

  1. 上一篇:煤粉燃烧和NO形成的数值模拟英文文献和中文翻译
  2. 下一篇:机械设计英文文献及中文翻译
  1. 层残余应力钢钛刀具磨损英文文献和中文翻译

  2. 数控车床上磨削主轴的分析

  3. 圆锥破碎机磨损模型英文文献和中文翻译

  4. 疏磨机设计英文文献和中文翻译

  5. 振动磨机英文文献和中文翻译

  6. 数控系统在平面磨床上应...

  7. 鄂式破碎机耐磨衬板英文文献和中文翻译

  8. 乳业同业并购式全产业链...

  9. 十二层带中心支撑钢结构...

  10. 大众媒体对公共政策制定的影响

  11. 电站锅炉暖风器设计任务书

  12. 当代大学生慈善意识研究+文献综述

  13. 酸性水汽提装置总汽提塔设计+CAD图纸

  14. 河岸冲刷和泥沙淤积的监测国内外研究现状

  15. 中考体育项目与体育教学合理结合的研究

  16. 杂拟谷盗体内共生菌沃尔...

  17. java+mysql车辆管理系统的设计+源代码

  

About

751论文网手机版...

主页:http://www.751com.cn

关闭返回