菜单
  

       The procedure just described readily shows that, according to both the EC3-ENV and EC3-EN, all the IMF design values of an unbraced sway orthogonal beam-and-column frame(NEd   NII , VEd   VII , MEd   MII) can be obtained,from the associated first-order values, by means of the common expression

       where (i) C is given by Eq. (10) and (ii) cr (i.e., Fcr ) is calculated on the basis of the first-order axial force profile due to the applied vertical loading.6 This explains why EC3-EN,unlike its ‘predecessor’ EC3-ENV, states explicitly that ‘For single storey frames designed on the basis of elastic global analysis, second order sway effects due to vertical loads may be calculated by increasing the horizontal loads and equivalent loads due to imperfections and other possible sway effects according to first order theory by the factor (1 − 1/cr )−1.’

    4. Second-order analysis of pitched-roof frames

       Let us consider the pitched-roof frame shown in Fig. 6(a),which is identical to the one depicted in Fig. 1(a) and is now subjected to the vertical (H) and horizontal (w =FEd/L) loads indicated in Fig. 6(b). Before addressing the geometrically nonlinear behaviour of this frame, it is important to recall some fundamental differences between the structural behaviours of pitched-roof and orthogonal (beam-and-column) frames :

      (i) In orthogonal frames, the way in which the (nodal) applied horizontal loads are distributed among the two column tops does not affect the corresponding sway displacements —they are always virtually identical. In pitched-roof frames,

    on the other hand, these displacements are only equal if the two horizontal applied loads are identical (due to the sloping rafters lateral stiffness).

      (ii) Symmetrical (geometry and vertical loading) orthogonal frames exhibit null displacements at the column tops. In vertically loaded symmetrical pitched-roof frames, there are no negligible ‘outward’ column sway displacements, which stem from the combined effect of the vertical displacement of the frame apex and the rafter inclination.

      (iii) It is a well-known fact that the first-order sway deformed configuration and bending moment distribution of a symmetrical orthogonal frame are exclusively due to the applied horizontal loads — this feature is very important, as the validity of the SAM is based on the similarity between these first-order results and their frame critical buckling mode counterparts [11]. In the next subsection,it will be shown that pitched-roof frames do not share this feature.

    4.1. First-order deformed configuration and bending momentdistribution

       It has been shown that it is possible to express the first-order deformed configuration and bending moment distribution of a pitched-roof frame acted on by the loads shown in Fig. 6(b) as the sum of the following three components, shown in Fig. 7(a)–(c):

      (i) The non sway components dN S and MN S, due to the vertical loading and assuming that the sway displacements are prevented by the horizontal reaction forces R — see Fig. 7(a).

      (ii) The symmetrical sway components dSS and MSS, which stem also from the vertical loading, through the application of horizontal forces opposite to the reactions R — see Fig. 7(b).

      (iii) The anti-symmetrical sway components dAS and MAS, due to the horizontal loads7 — see Fig. 7(c).

       It is still worth mentioning that the maximum MSS values are very often considerably larger than the corresponding MAS ones — indeed, the two charts presented in Fig. 8(a) (fixedbase frames) and 8(b) (pinned-base frames) provide values that lead to a straightforward evaluation of the ratio between the maximum MSS and MAS values: for any given geometry (RL = Lr /Lc, RH = RL sin  , R = IcLr /Lc Ir ) and loading (FEd = wL, HEd = 2H) combination, the determination of   = MSS. max/MAS. max just requires the multiplication of  0 or  1, (read from the appropriate chart) by the factor (FEd/HEd )(RL cos  /18). In frames with semi-rigid column bases (K = kcLc/E Ic),   can be approximately estimated by means of

  1. 上一篇:钢筋混凝土柱在火灾中的性能模拟英文文献和中文翻译
  2. 下一篇:耦合侧向扭转频率的不对称三维框架结构英文文献和中文翻译
  1. 层残余应力钢钛刀具磨损英文文献和中文翻译

  2. 舰船玻璃钢夹芯板缺陷和...

  3. 冷轧带钢的工业形状检测...

  4. 冷弯钢门户框架的设计方...

  5. 钢筋混凝土柱在火灾中的...

  6. 通过增量动态分析评估设...

  7. 加强钢框架连接和有限元...

  8. 大众媒体对公共政策制定的影响

  9. 当代大学生慈善意识研究+文献综述

  10. 十二层带中心支撑钢结构...

  11. 杂拟谷盗体内共生菌沃尔...

  12. java+mysql车辆管理系统的设计+源代码

  13. 电站锅炉暖风器设计任务书

  14. 中考体育项目与体育教学合理结合的研究

  15. 河岸冲刷和泥沙淤积的监测国内外研究现状

  16. 乳业同业并购式全产业链...

  17. 酸性水汽提装置总汽提塔设计+CAD图纸

  

About

751论文网手机版...

主页:http://www.751com.cn

关闭返回