-
【摘要】车削加工过程中常常发生振动现象，这种有害振动会使工件表面产生振纹，严重影响其形状精度、尺寸精度、位置精度和表面粗糙度。因此，分析研究车削加工中振动产生的原因并采取相应的措施来消除或减小振动是非常必要的。本文主要研究主轴转速对车刀三向振动频域特性的影响，试验以济南车床生产的卧式车床 为试验平台，利用三向加速度传感器测得新刀、中等磨损、严重磨损三种刀具下表面的振动信号，使用北京波谱公司的WS-DAQ振动信号采集仪与其配套的 频谱分析软件来采集、分析测得的振动信号，得到了刀具振动加速度信号的自功率谱密度曲线。结果表明: （1）随着主轴转速的增大，车刀在轴向、径向、切向三个方向上的最大自功率谱密度值先减小后增大，在1600r/min左右时，自功率谱最小;（2）不管主轴转速如何改变，在径向上的自功率谱一直最大，切向居中，轴向最小;（3）在切削过程中，不管是在三种不同的切削方向，还是三种不同磨损程度的车刀，刀具最大自功率谱所对应的振动频率都保持不变，大约为50Hz。39782
- 上一篇：ANSYS的PBGA电子元器件结构优化设计
- 下一篇：主轴转速对车刀三向振动时域特性影响的试验设计
【毕业论文关键词】车削振动；三向加速度；频域分析；自功率谱密度
The Experimental Design of the Effect of Spindle Speed on the Frequency Domain Characteristic of Tool Three-way
Turning Vibration
【Abstract】It always causes chattering in the process of turning. This harmful vibration will make the surface chatter and have a great influence to shape accuracy, dimensional accuracy, position accuracy and surface roughness. Therefore, it is necessary to analyze the reasons of the turning vibration and take appropriate measures to eliminate or reduce the vibration. This paper studies the effect of the spindle speed on the frequency domain characteristic of tool three-way vibration , which uses the horizontal lathes of CJK6136-MATE-360×570 produced by Jinan lathes as tentative platform and uses three-acceleration sensor to measure vibration singals generated by the sword surface of the three kinds of tools of the elementary wear, moderate wear and severe wear and uses Beijing's WS-DAQ vibration signal acquisition instrument with matching spectral analysis software to capture, analyze vibration signals measured to obtain the self-power spectral density curve of tool vibration acceleration signals . The results show that: (1) With the spindle speed increases, the largest self- power spectral density in three directions of axial, radial, tangential is reduced after the first increase .When the spindle speed is in 1600r / min or so, the self-power spectrum is the smallest. (2) Regardless of the changes of the spindle speed , the self-power spectrum in the radial direction has the maximum, tangential direction center, a minimum in the axial direction; (3) During the cutting process, whether it is in three different cutting direction, or three different degree of wear of tools, tools from the power spectrum corresponding to the maximum vibration frequency remains about 50Hz.
【Keyword】Turning vibration; Three-acceleration; Frequency domain analysis; Self-power Spectral Density
目 录
摘要 1
1 绪论 5
1.1研究意义 5
1.2研究现状 5
1.3课题研究内容 7
1.4课题研究方法和技术路线 7
1.4.1研究方法 7
1.4.2技术路线 8
2 机械振动测量理论基础 9
2.1振动的基本原理 9
2.2振动测量参数 9
2.3测振传感器与放大器 10
2.3.1测振传感器 10
2.3.2测振放大器 13
2.3.3传感器的选择 14
3 振动信号频域分析理论基础 15
-
发动机润滑油对汽车NVH性能的影响研究
-
180mm单室双推火箭弹设计
-
骨料对混凝土侵彻性能的影响
-
ansys微型钻头的钻头参数对...
-
反恐排爆机器人设计
-
MATLAB直流电动机控制建模及转速控制算法设计
-
EX-106数控车床主轴结构优化设计+CAD图纸
酸性水汽提装置总汽提塔设计+CAD图纸
乳业同业并购式全产业链...
电站锅炉暖风器设计任务书
十二层带中心支撑钢结构...
java+mysql车辆管理系统的设计+源代码
大众媒体对公共政策制定的影响
杂拟谷盗体内共生菌沃尔...
河岸冲刷和泥沙淤积的监测国内外研究现状
中考体育项目与体育教学合理结合的研究
当代大学生慈善意识研究+文献综述