毕业论文

打赏
当前位置: 毕业论文 > 机械论文 >

计量式柱塞泵密封结构分析+CAD图纸+答辩PPT

时间:2017-01-02 15:11来源:毕业论文
摘要:柱塞泵是液压系统的一个重要装置。它依靠柱塞在缸体中往复运动,使密封工作容腔的容积发生变化来实现吸油、压油。柱塞泵具有额定压力高、结构紧凑、效率高和流量调节方

摘要:柱塞泵是液压系统的一个重要装置。它依靠柱塞在缸体中往复运动,使密封工作容腔的容积发生变化来实现吸油、压油。柱塞泵具有额定压力高、结构紧凑、效率高和流量调节方便等优点,被广泛应用于高压、大流量和流量需要调节的场合,诸如液压机、工程机械和船舶中。根据实验经验所得,泵筒、活塞杆和压盖三者之间存在一定的间隙,导致流体从中泄露出来,所以需要进行密封,而本课题对柱塞泵采用了O型圈及聚四氟乙烯填料环的接触密封,在沟槽中安装O形圈,并且在O形圈两侧分别加上一个挡圈,在受压力的作用下,防止O形圈往压力方向的间隙挤出变形以致失效。在填料函里面装上4个聚四氟乙烯填料环,其材料具有较好的弹性,在受压力作用,可以得到缓冲,使其对O形圈的作用力减小,防止O型圈挤入运动副的间隙中。在端盖上安装O形圈,对泵结构进行了多重密封,保证其密封性。4888
关键词:  柱塞泵;O形密封圈;填料环
Structure analysis of sealing metering plunger pump
Abstract: The plunger pump is an important means of the hydraulic system. It relies on the plunger reciprocates in the cylinder, so that the sealing capacity of the volume of the cavity changes to achieve Suction pressure oil. Piston pump rated pressure, compact structure, high efficiency, easy adjustment and flow, is widely used in high-pressure, flow and flow need to adjust the occasion, such as hydraulic machines, construction machinery and shipbuilding. There are gaps between the pump cylinder, the piston rod and gland leading fluid from leaked according to the test of experience, so they need to be sealed. The plunger pump of the subject uses O sealing ring and PTFE packing ring seal. The O-ring is installed in the groove, and on both sides of the O-ring is respectively with a snap ring in order to prevent O-ring extrusion gap toward the direction of the pressure from deformation resulting in failure under pressure. The inside of the stuffing box fitted with four PTFE packing rings whose material has good flexibility. Under the pressure force can be buffered, so that the biasing force of the O-ring is reduced to prevent a gap in the O-ring squeeze motion pair. O-ring installed on the end cap is multiple sealing of the pump structure in order to ensure its tightness.
KeyWords :  Plunger pump; O sealing ring; Packing ring
目录
绪论    3
1 柱塞泵    5
1.1 柱塞泵的现状和发展    5
1.2 柱塞泵的主要参数    8
2 活塞杆的设计    10
2.1 滑动螺旋传动的设计    10
2.1.1 螺杆螺母材料的选取    11
2.1.2 按耐磨性计算螺杆中径    12
2.1.3 自锁性验算    13
2.1.4 螺杆强度验算    13
2.1.5 螺母螺纹强度验算    14
2.1.6 螺杆的稳定性验算    14
2.2 活塞杆的设计    15
2.2.1 活塞杆的强度校核    15
2.2.2 活塞杆的稳定性    17
2.3 导向套的设计    18
3 缸体的设计    20
3.1缸体壁厚的计算    20
3.2液压缸出口直径的设计    21
3.3缸底厚度的计算    22
3.4阀门的选择    22
4 密封结构    24
4.1 O形密封圈、挡圈及沟槽尺寸    24
4.1.1 沟槽和O形圈的尺寸    27
4.1.2 O形圈的公差尺寸    28
4.1.3 沟槽尺寸    29
4.2 软填料密封的设计    30
4.2.1 填料箱主要结构尺寸    31
4.2.2 压盖螺栓直径计算    31 计量式柱塞泵密封结构分析+CAD图纸+答辩PPT:http://www.751com.cn/jixie/lunwen_1700.html
------分隔线----------------------------
推荐内容