菜单
  

    point load. On the basis of the observed experimental deformed profiles it has been found that the shells deform
    in axisymmetric mode of collapse. Load–compression curves of the deformed specimens are studied. A Finite
    Element computational study of the development of this axisymmetricmode of collapse is also carried out using
    FORGE2 [11] code to propose a computational model. Computational model has been verified by comparing
    the experimental and computed results of the deformed shapes and their corresponding load–compression and
    energy–compression curves. On the basis of the variations of the computed strains and stresses the mechanics
    of the mode of collapse has been studied and discussed.
    2 Experimental work
    Aluminium hemispherical shells of R/t ranging between 25 and 43 were compressed between flat platen and
    a hemispherical mandrel on a Universal testing INSTRON machine (see Table 1). A hemispherical nosedmandrel having 22mm diameter and 85mm length made up of hardened tool steel was used for applying con-
    centrated load on the shell [8]. Commercially available aluminium sheets of standard thickness were obtained
    and the spherical shell specimens used in the experiments were made by the process of spinning. Shells of
    different radius and thickness were obtained. The shells were filled with emulsion of plaster of Paris and dried.
    By holding these shells in lathe machine the edges were cut for accuracy with respect to the axis of shells.
    The shells were tested in as-received condition. The shells were placed on the stationary flat platen and the
    hemispherical mandrel fixed on the moving crosshead was moved in downward direction on its axis with a
    speed of 2mm/min. Figure 1a shows the loading arrangement for the experimental work. Load versus cross-
    head movement plot was obtained from the chart recorder of the machine. The experiments were interrupted at
    regular intervals for studying the mode of collapse and for the measurements of radius of rolling plastic hinge
    rp. Compression was continued up to 40–50mm movement of the mandrel in downward direction. The radius
    of rolling plastic hinge rp was measured at selected number of sections at any typical stage of compression;
    an average of the readings was obtained. For this measurement the radius gauges were used.3 Experimental results
    All the shells were collapsed in an analogous mode of deformation throughout the compression process. Dur-
    ing the compression of a typical spherical shell (see Fig. 1b), two stages of deformation were noticed. These
    are designated as stage I and stage II. In the beginning of the compression process up to few milimeters of
    compression all the spherical shells were deformed with formation of a small indent at the point of contact of
    shell with the mandrel along with the local flattening of the adjoining area. This was designated as the stage I
    deformation. It was observed that as the value of R/t increases the range of compression over which the stage
    I deformation occurs decreases.With the progress of compression an axisymmetric inward dimple was formed
    due to the development of a rolling plastic hinge; this is the stage II deformation. In the stage II deformation
    with increase in compression (h) the axisymmetric inward dimple expands due to the radial outwardmovement
    of the rolling plastic hinge.
    It is already seen that over a large range of compression of spherical shells an inward dimple formation
    takes place and with progress of compression this axisymmetric inward dimple expands due to the radial
    outward movement of the rolling plastic hinge. As a result the radius of rolling plastic hinge rp decreases with
    the progress of compression.
    It was found that for all the shell specimens the load in the load–compression curve increased continuously
    throughout the compression process (see Fig. 5a). The rate of increase in load decreased with increase in R/t
  1. 上一篇:散热器恒温阀英文文献和中文翻译
  2. 下一篇:注塑模具英文文献及中文翻译
  1. 金属板料冲压模具计算机...

  2. 金属薄板剪切机英文文献和中文翻译

  3. 废弃电路板非金属粉作为...

  4. 齿轮箱外壳综合设置和夹...

  5. AA2024-T3可成形性金属板英文文献和中文翻译

  6. 塑料吹塑金属成型英文文献和中文翻译

  7. 卧式壳管式冷凝器英文文献和中文翻译

  8. 杂拟谷盗体内共生菌沃尔...

  9. 电站锅炉暖风器设计任务书

  10. 当代大学生慈善意识研究+文献综述

  11. 十二层带中心支撑钢结构...

  12. 乳业同业并购式全产业链...

  13. 河岸冲刷和泥沙淤积的监测国内外研究现状

  14. 大众媒体对公共政策制定的影响

  15. 酸性水汽提装置总汽提塔设计+CAD图纸

  16. java+mysql车辆管理系统的设计+源代码

  17. 中考体育项目与体育教学合理结合的研究

  

About

751论文网手机版...

主页:http://www.751com.cn

关闭返回