菜单
  

    Selected  Molding  Conditions.Prior  to  studying  the  effects
    of  the VAIM  process,  a  large  number  of  specimens  were  molded
    and  mechanically  tested.  Through  an  optimization  process  a  full
    set  of  conventional  molding  conditions  that  yielded  the  strongest
    products  was  determined.  As  it  turned  out,  the  optimal  molding
    conditions  for  the  virgin  material  exactly  matched  those  for  the
    recycled  material.  These  conditions  are  presented  in  Table  1.
    Since  the  optimal  molding  conditions  for  100%  virgin  and  100%
    recycled  PS  were  found  to  be  identical,  it  was  concluded  that these  conditions  would  also  be  best  for  the  blended  mixtures.Thus,  throughout  the  remainder  of  the  investigation,  the  processing  conditions  shown  in  Table  1  were  applied  regardless  of whether  or  not  vibration  assistance  was  utilized.
    Table 1 Optimized molding conditions utilized throughout the
    investigation
    Injection  time 0.5  s
    Holding  time 19.5  s
    Cooling  time 15  s
    Injection  pressure 45  Mpa
    Holding  pressure 45  Mpa
    Mold  temperature 70°C
    Nozzle  temperature 210°C
    Barrel  temperature ( front) 205°C
    Barrel  temperature (rear )200°C
    Range of Vibration Parameters Studied. The hydraulic system  of  the  BOY  15S  molding  machine  is  capable  of  producing suitable  injection  screw  oscillations  at  frequencies  up  to  9  Hz.Therefore,  the  frequency  range  studied  during  the  present  effort was  from  1  to  8  Hz.  The  delay  times  to  begin  vibration  ranged from 0.0 to 1.0 s, and vibration duration levels ranged from 4.0 to 12.0 s. Lastly, duty cycles between 1.0 and 3.0 were investigated.
    Within  the  window  of  the  parameter  levels  specified   above,  an experimental optimization process was carried out that focused on arriving  at  sets  of  VAIM  processing  conditions  that  would  yield the  strongest  products  for  each  of  the  material  blends  studied.During  this  process,  approximately  900  sample  specimens  were manufactured  and  tested  for  each  material  combination.  The  results  that  were  generated  are  presented  throughout  the  remainder of  this  paper.
    Results  and  Discussion
    Baseline  Results. To  study  the  effects  of  VAIM  processing,results  with  conventionally  molded  products  needed  to  be  obtained first  for comparison purposes. Along this line, 30 test specimens were produced from both the 100% virgin (100/0 hereafter),100% recycled (0/100 hereafter), 75%/25% virgin/recycled (75/25Hereafter),  and  50%/50%  virgin/recycled (50/50  hereafter) PS blends  using  the  optimized  conventional  molding  conditions  discussed  earlier. These  samples  were  then  mechanically  tested,  and the  ultimate  tensile  strength (UTS) distributions  that  resulted  are shown  in  Fig.  1.
  1. 上一篇:建筑空调英文文献和中文翻译
  2. 下一篇:鼓泡塔反应器英文文献和中文翻译
  1. 木质填料聚丙烯复合材料...

  2. 材料选择英文文献和中文翻译

  3. 塑料制品的注塑模具设计...

  4. 变形地基上的土工合成材...

  5. 三维编织复合材料力学性...

  6. 节能墙体材料数据库和数...

  7. 氧化锌纳米材料的合成英文文献和中文翻译

  8. 十二层带中心支撑钢结构...

  9. 中考体育项目与体育教学合理结合的研究

  10. 大众媒体对公共政策制定的影响

  11. java+mysql车辆管理系统的设计+源代码

  12. 电站锅炉暖风器设计任务书

  13. 酸性水汽提装置总汽提塔设计+CAD图纸

  14. 河岸冲刷和泥沙淤积的监测国内外研究现状

  15. 乳业同业并购式全产业链...

  16. 杂拟谷盗体内共生菌沃尔...

  17. 当代大学生慈善意识研究+文献综述

  

About

751论文网手机版...

主页:http://www.751com.cn

关闭返回