菜单
  

    10.5 Combustion Processes and Fuels
    The primary source of energy in a heating boiler is the combustion of
    a fossil fuel—coal, oil, or gas—or waste materials. The use of peat,
    garbage, sawdust, petroleum coke, and other waste products is in-
    creasing, but it is still a small fraction of the total fuel burned in this
    country.
    Combustion is a process of burning—combining the fuel with oxygen
    and igniting the mixture. The result is heat release, absorbed through
    radiation, convection, and, to some degree, conduction.
    10.5.1 The combustion process
    The combustion process follows basic principles called the three T’s of
    combustion. The first one is time—the time required for the air to
    properly mix with the fuel and for the combustion process to be com-
    pleted. It is critical when waste materials are being combusted in con-
    junction with standard fuels. The second is temperature—the temper-
    ature at which the fuel will ignite, oxidation is accelerated, and the
    process of combustion begins. Ignition temperatures are well estab-
    lished for standard fossil fuels but must be carefully considered when
    waste or other organic-type materials are being burned. The third is
    turbulence—the process of thoroughly mixing the air and fuel so that
    each particle of fuel is in contact with the right amount of oxygen and
    combustion can continue to completion. The turbulence must be vio-
    lent enough to ensure good contact between the fuel and the oxygen.
    Assuming there is enough combustion air to work with, inadequate
    turbulence is the most common cause of incomplete combustion. In-
    adequate turbulence can result in the generation of excessive amountsof carbon monoxide, and combustion may continue well beyond the
    furnace portion of the boiler.
    10.5.2 The chemical reaction
    In its simplest form, the combustion of natural gas (methane, CH4)
    with air as a source of oxygen, the chemical reaction can be written
    CH  2(4N  O) ⇒ CO  2H O  8N  heat 422222
    This describes a perfect and complete or stoichiometric combustion
    process. In practice, the process is never perfect or complete. Some
    carbon monoxide is formed, and some contaminants, such as sulfur,
    are present and enter into the process. Sulfuric and nitric acids and
    nitrous oxides are often formed, along with other undesirable com-
    pounds.
    10.5.3 Excess air
    Because the combustion process is never perfect and perfect mixing of
    air and fuel is never achieved, every combustion process requires ex-
    cess air. Excess air is the additional air that must be added to the
    theoretically perfect mixture to ensure as complete a combustion pro-
    cess as is practically possible. The larger the amount of excess air, the
    lower the combustion efficiency. Often overlooked is the possibility of
    condensation in the boiler or flue that has too much excess air. It can
    be reasoned that turbulence is a most important factor in the com-
    bustion process. Almost all of the newest boiler developments have
    been in burner design, in an attempt to improve the mixing of air and
    fuel to minimize excess air, to maximize combustion efficiency, and to
    minimize the generation of nitrous oxides.
    10.5.4 Combustion efficiency
    The combustion efficiency is the ratio of fuel heat input minus the
    stack loss (through the chimney or vent), pided by the fuel heat
    input. Typical efficiencies for mechanically fired boilers range from 75
    to 83 percent for new installations at full-load conditions. Firing at
    reduced capacity may reduce the combustion efficiency. Therefore it is
    desirable to match the boiler to the load as closely as possible or to
    use multiple boilers.
    The overall thermal efficiency is the gross output in Btu/h pided
  1. 上一篇:复合材料高强度混凝土桥梁英文文献和中文翻译
  2. 下一篇:塑料注射成型英文文献和中文翻译
  1. 汽车乘员舱的声振耦合英文文献和中文翻译

  2. 立体光照成型的注塑模具...

  3. 数控机床英文文献和中文翻译

  4. 工业机械手英文文献和中文翻译

  5. 低频振动的铁路车轴的状...

  6. 接头的形状对沥青塞接头...

  7. 数控加工技术英文文献和中文翻译

  8. 电站锅炉暖风器设计任务书

  9. 河岸冲刷和泥沙淤积的监测国内外研究现状

  10. 当代大学生慈善意识研究+文献综述

  11. java+mysql车辆管理系统的设计+源代码

  12. 杂拟谷盗体内共生菌沃尔...

  13. 大众媒体对公共政策制定的影响

  14. 乳业同业并购式全产业链...

  15. 酸性水汽提装置总汽提塔设计+CAD图纸

  16. 十二层带中心支撑钢结构...

  17. 中考体育项目与体育教学合理结合的研究

  

About

751论文网手机版...

主页:http://www.751com.cn

关闭返回