菜单
  

    parameters are modified to the direction of minimizing the difference between the calculated output and targeted output during training.
    3.2.2 Formation of decision making pattern
    In order to create the decision making pattern, computation of the maximums and minimums of two objective functions within a proper range of the process factors that cover a slightly wider scope than that of the experiments should be initially carried out. Once the maximum and minimum of the objective functions are determined, the scaled values of the objective functions within the range are regularly arranged on a two-dimensional table and every possible combination of two objective functions within the range is ranked with respect to the supervisor’s preference. The final decision making pattern is completed by scaling
    the ranking into values between 0 and 1. Figure 3 demonstrates the surface of the NN decision maker where the approximation errors at the sampling points can be ignored.
    3.2.3 Structure of NN decision maker and error back-propagation
    The NN decision maker has the structure of a multi-layer neural network that consists of an input layer, four hidden layers and an output layer, which can be expressed as 2-6-8-7-5-1. The main advantage of multi-layer neural networks exists in the generalization ability for nonlinear systems. By training the finite number of a discrete data set,a system that responds to continuous inputs can be created respectively. The convergence condition of the least square error is resolved at 0.0001, and after about 20,000 cycles,training is terminated.
    4 Results and discussions
    The thixoforging experiments were performed under the experimental conditions, and the pistons were obtained as shown in Fig. 4.In order to measure the hardness of the products, the piston was cut vertically. Figure 5 shows the measurement location for the hardness test. Rockwell (B scale) was used for the hardness test. Hardness value, hardness average,and standard deviation are shown in Table and a prediction of values beyond the trained data is possible, which is similar to nonlinear interpolation. Error back propagation, one of the neural network training skills, has been a model for multi-layer neural networks. It does not use a sort of feedback operation but errors are back-propagated to modify the connection factors, such as connection weights and momentums of neural networks during training. The following equations explain the mechanics of error back propagation for the multi-layer neural network.
    Here, Wji(t) is a connection weight between neurons,ΔWji(t) is the gradient of Wji(t), t is the number of the training cycle, Oi is an output value of the ith neuron, Oj is the output value of the jth neuron, and dj is the expected output of the jth neuron.  is the differential value of the sigmoid function jth neuron at the middle layers, η is the learning rate, and α is the momentum factor.Learning rate parameters play a role in scaling the adjustments to weights, and momentum factors are used in scaling the adjustments from a previous iteration and then
    are added to the adjustments in the current iteration. The least square error is used as convergence measure. It is also known as error of delta rule (Eq. 8). In this study, learning rate and momentum factor are set to 0.7 and 0.9, respectively. The convergence condition of the least square error is resolved at 0.0001, and after about 20,000 cycles, training is terminated. 4 Results and discussions The thixoforging experiments were performed under the experimental conditions, and the pistons were obtained asshown in Fig. 4. In order to measure the hardness of the products, the piston was cut vertically. Figure 5 shows the measurement location for the hardness test. Rockwell (B scale) was used
    for the hardness test. Hardness value, hardness average, and standard deviation are shown in Table 1.
    4.1 Variation analysis of the process factors
    The aim of variation analysis is to verify the influence of the process factors, such as the die temperature, the liquid fraction and compression holding time on the goal factors, such as the hardness average and the standard deviation of hardness. Tables 2 and 3 describe the result of variation analysis about the 23 factorial designs which is the former
  1. 上一篇:真空电弧沉积系统英文文献和翻译
  2. 下一篇:夹点分析原油蒸馏塔的设计英文文献和中文翻译
  1. 汽车乘员舱的声振耦合英文文献和中文翻译

  2. 汽车发动机连杆英文文献和中文翻译

  3. KBE汽车覆盖件冲压工艺路...

  4. 汽车热交换系统英文文献和中文翻译

  5. 船用柴油发动机的活塞组件英文文献和翻译

  6. 汽车安全带英文文献和中文翻译

  7. 铝合金结构特性英文文献和中文翻译

  8. 十二层带中心支撑钢结构...

  9. 酸性水汽提装置总汽提塔设计+CAD图纸

  10. 河岸冲刷和泥沙淤积的监测国内外研究现状

  11. 大众媒体对公共政策制定的影响

  12. 当代大学生慈善意识研究+文献综述

  13. java+mysql车辆管理系统的设计+源代码

  14. 乳业同业并购式全产业链...

  15. 杂拟谷盗体内共生菌沃尔...

  16. 中考体育项目与体育教学合理结合的研究

  17. 电站锅炉暖风器设计任务书

  

About

751论文网手机版...

主页:http://www.751com.cn

关闭返回