菜单
  
    Design Optimization of Shell and Tube Heat Exchanger by Vibration Analysis
    Abstract  In this paper a simplified approach to optimize the design of Shell Tube Heat Exchanger [STHE] by flow
    induced vibration analysis [FVA] is presented. The vibration analysis of STHE helps in achieving optimiza-
    tion in design by prevention of tube failure caused due to flow induced vibration. The main reason for tube
    failure due to flow induced vibration is increased size of STHE. It is found that in case of increased size of
    STHE, the surface area and number of tubes increases, thus the understanding and analysis of vibration be-
    comes a very difficult task. Again it is found that flow induced vibration analysis is considered as an integral
    part of mechanical & thermal design of STHE. The detailed design, fabrication, testing and analysis work
    was carried out at Alfa Laval (India), Ltd., Pune-10.5494
     
    Keywords: Heat Exchanger, Flow-Induced Vibration, TEMA, HTRI
    1. Introduction  
    The principal culprit in flow induced vibration of tubes
    of STHE is the unsupported tube lengths subjected to
    large flow rates on shell side. The increased size of
    STHE due to large flow rates is responsible for vibration
    of tubes, which further leads to tube failure. Also the
    design of STHE is made safer by modifying shell type
    and/or baffles style and baffle design. Thus, the vibration
    analysis is of utmost importance in design of STHE. So,
    the flow induced vibration analysis is considered as an
    integral part of thermal design.
    The characteristics of vortex shedding from tube banks
    with closely mounted serrated fin was investigated in [1]
    where the relationship between the Strouhal number de-
    fined by the equivalent diameter as the characteristic
    length of a finned tube in the tube banks and the Strouhal
    number map for bare-tube banks was examined. Whereas
    in [2] the author has presented various outlet conditions
    of a shell and tube heat exchanger theoretically and ex-
    perimentally in which it is observed that prime parameter
    geometry of outlet affects the performance, maintenance
    and life span of a vertical shell and tube evaporator. The
    heat transfer enhancement has been achieved in [3], by
    modifying the configuration of a shell-and-tube heat ex-
    changer, through the installation of sealers in the shell-
    side. The gaps between the baffle plates and shell is
    blocked by the sealers, which effectively decreases the
    short-circuit flow in the shell-side. The original short-
    circuit flow then participates in heat transfer, which in-
    tensifies the heat transfer  performance inside the heat
    exchanger. The use of a non-traditional optimization tech-
    nique; called Particle Swarm Optimization (PSO), for
    design optimization of shell-and-tube heat exchangers
    from economic view point is explored in [4] in which
    minimization of total annual cost is considered as an ob-
    jective function. Three design variables such as shell
    internal diameter, outer tube diameter and baffle spacing
    are considered for optimization. Two tube layouts viz.
    triangle and square are also considered for optimization.
    The results of optimization using PSO technique are
    compared with those obtained by using Genetic Algo-
    rithm (GA). Also the optimization of the design of shell-
    and-tube heat exchangers by minimization of the thermal
    surface of the equipment, for certain minimum excess
    area and maximum pressure drops, considering discrete
    decision variables is presented in [5]. The heat transfer
    coefficient and pressure drop on the shell side of a
    shell-and-tube heat exchanger has been obtained experi-
    mentally in [6] for three different types of copper tubes.
     
    The comprehensive experimental investigation on the
  1. 上一篇:洁净空间及洁净室英文文献和翻译
  2. 下一篇:空调房间空气质量的研究英文文献和翻译
  1. 便携式电子硫化机效率英文文献和中文翻译

  2. 主轴自振式钻头的加工预...

  3. 沥青填充式伸缩缝英文文献和中文翻译

  4. 平行和分布式作业破碎机英文文献和中文翻译

  5. 双曲柄环板式针摆线齿轮...

  6. 质量有缺陷的滚动轴承振...

  7. Web2.0的网络广告模式英文文献和中文翻译

  8. 杂拟谷盗体内共生菌沃尔...

  9. 十二层带中心支撑钢结构...

  10. 酸性水汽提装置总汽提塔设计+CAD图纸

  11. 河岸冲刷和泥沙淤积的监测国内外研究现状

  12. 大众媒体对公共政策制定的影响

  13. 电站锅炉暖风器设计任务书

  14. 中考体育项目与体育教学合理结合的研究

  15. 当代大学生慈善意识研究+文献综述

  16. 乳业同业并购式全产业链...

  17. java+mysql车辆管理系统的设计+源代码

  

About

751论文网手机版...

主页:http://www.751com.cn

关闭返回