菜单
  

    2.4 Module for mold modeling (core and cavity design and design all residual mold components; module IV).
    This module is used for CAD modeling of the mold (core and cavity design). This module uses additional software tools for automation creating core and cavity from simulation(reference) model including shrinkage factor of plastics material and automation splitting mold volumes of the fixed and movable plates. The structure of this module is shown .
    Additional capability of this module consists of software tools for:
    Applying a shrinkage that corresponds to design plastic part, geometry, and molding conditions, which are computed in module for numerical simulation.
    Make conceptual CAD model for nonstandard plates and mold components.
    Design impression, inserts, sand cores, sliders and other components that define a shape of molded part.
    Populate a mold assembly with standard components such as new developed mold base which consists of DM-E mold base and mold base of enterprises which use this system, and CAD modeling ejector pins, screws, and other components creating corresponding clearance holes.
    Create runners and waterlines, which dimension was calculated in module for calculating of parameters of injection molding and mold design calculation and selection.
    Check interference of components during mold opening, and check the draft surfaces
    After applied dimensions and selection mold components, user loads 3D model of the fixed (core) and movable (cavity) plate. Geometry mold specifications, calculated in the previous module, are automatically integrated into this module, allowing it to generate the final mold assembly. Output from this module receives the complete mold model of the assembly as shown. This module allows modeling of nonstandard and standard mold components that are not contained in the mold base.
    3 Case study
    The complete theoretical framework of the CAD/CAE-integrated injection mold design system for plastic products was presented in the previous sections. In order to complete this review, the system was entirely tested on a real case study. The system was tested on few examples of similar plastic parts. Based on the general structure of the model of integrated CAD/CAE design system shown in Fig. 1, the authors tested the system on some concrete examples. One of the examples used for verification of the test model of the plastic part is shown in Fig. 6.
    The module for the numerical simulation of injection molding process defines the optimal location for setting gating subsystem. Dark blue regions indicate the optimal position for setting gating subsystem as shown.
    Based on dimensions, shape, material of the case study product, optimal gating subsystem location, and injection molding parameters (Table 1), the simulation model shown was generated.
    One of the rules for defining simulation model gate for numerical simulation:
    IF (tunnel, plastic material, mass) THEN prediction dimension (upper tunnel, length, diameter1, diameter2, radius, angle, etc.)
    Part of the output results from module II, which are used in module III are shown in Table 1.
    Material grade and material supplier    Acrylonitrile butadiene styrene 780 (ABS 780), Kumho Chemicals Inc.
    Max injection pressure    100 MPa
    Mold temperature    60°C ili 40
    Melt Temperature    230°C
    Injection Time    0,39 s 0,2 s
    Injection Pressure    27,93 MPa
    Recommended ejection temperature    79°C
    Modulus of elasticity, flow direction for ABS 780    2,600 MPa
    Modulus of elasticity, transverse direction for ABS 780    2,600 MP
    Poision ratio in all directions for ABS 780    0.38
    Shear modulus for ABS 780    942 MPa
    Density in liquid state    0.94032 g/cm3
    Density in solid state    1.047 g/cm3
  1. 上一篇:活动膝盖康复矫正装置英文文献和翻译
  2. 下一篇:蠕动运动蠕虫仿生机器人英文文献和翻译
  1. 立体光照成型的注塑模具...

  2. CAD/CAM模具技术课程教学改...

  3. 木质填料聚丙烯复合材料...

  4. 对热流道系统注塑工艺英文文献和中文翻译

  5. 注塑模具的设计及其热分...

  6. 注塑模具设计英文文献和中文翻译

  7. CAD知识的模具设计英文文献和中文翻译

  8. java+mysql车辆管理系统的设计+源代码

  9. 十二层带中心支撑钢结构...

  10. 当代大学生慈善意识研究+文献综述

  11. 中考体育项目与体育教学合理结合的研究

  12. 杂拟谷盗体内共生菌沃尔...

  13. 河岸冲刷和泥沙淤积的监测国内外研究现状

  14. 乳业同业并购式全产业链...

  15. 电站锅炉暖风器设计任务书

  16. 大众媒体对公共政策制定的影响

  17. 酸性水汽提装置总汽提塔设计+CAD图纸

  

About

751论文网手机版...

主页:http://www.751com.cn

关闭返回