- 上一篇：钢筋混凝土倒T梁采用锚固CFRP片材的修复英文文献和中文翻译
- 下一篇：注射成型过程中的聚丙烯填充物英文文献和中文翻译
j=0 Bi,k(u) · Bj,l(v) · wi,j · Ci,j; its partial
(3) are satisfied only by a group of points on these surfaces (see the
derivative with respect to parameter u is Nmu(u, v) =
green surfaces in Fig. 7(a)). The second is the ‘partially obscured Bu
surface’ in which only a part of its area is obscured by other surfaces
Bj,l(v) · wi,j so that its partial derivative with respect to parameter u
Fig. 7. (a) Dual moldable surfaces and (b) partially obscured surface. (For interpretation of the references to color in this figure legend, the reader is referred to the web version of this article.)
Fig. 8. Surface regions pided from dual moldable surfaces.
is the derivative
of a B-spline basis function and can be expressed by the following
equation:
Bu k − 1
k − 1
i,k(u) = u
i+k −
Bi,k−1(u) +
ui u
i+k+1 −
ui+1
Bi+1,k−1(u). (7)
Therefore, the partial derivative of S(u, v) with respect to u is:
∂S(u, v)
∂u =
Nm(u, v) ′
Dn(u, v)
u
Nm′ (u, v) · Dn(u, v) − Dn′ (u, v) · Nm(u, v)
u u
= Dn2(u, v)
Nm′ (u, v) · Dn(u, v) − Dn′ (u, v) · Dn(u, v) · S(u, v)
u u
= Dn2(u, v)
Fig. 9. Division of a partially obscured surface s1 into two surface regions.
figure, surface s1 is partially obscured by surface s2. Each boundary edge of s2 is used to build an extrusion surface s3 along the current parting direction. The intersection between surface s1 and surface s3 can then be used to pide s1 into an un-obscured region and an
Nm′ (u, v) − Dn′ (u, v) · S(u, v)
u u . (8)
Dn(u, v)
Similarly, the partial derivative of S(u, v) with respect to v is:
obscured region.
Fig. 10 shows an example of the surface regions pided from a partially obscured surface of the part in Fig. 5. The red surface is partially obscured by others when viewed from infinity along
∂S(u, v)
∂v =
Nm′ (u, v) Dn′ (u, v) S(u, v)
u u (9)
Dn(u, v)
directions −d3 , −d5 , and −d6 . The edge-extrusion algorithm is
thus applied, resulting in the eleven surface regions pided from
A silhouette curve can be found by substituting Eqs. (6)–(9) into Eq. (5). In fact, Eq. (5) is a polynomial equation of two variables u and v. In this scenario, there are fewer equality constraints than there are variables. Its zero-solution set can be computed based on the convex hull and subpision properties of rational spline functions. A set of discrete points approximating the zero set is generated by recursive subpision based on the Newton–Raphson method. The method to solve a general system of m polynomial equations of n variables is described by G. Elber and M.S. Kim [23]. Fig. 8 shows an example of surface regions pided from dual mold- able surfaces of the pedal part in Fig. 5.