铜钢双丝焊接头的组织性能研究

摘要本文采用硅青铜+钢焊丝对铜T2和钢Q235异种金属进行双丝焊焊接试验研究。因焊丝直径都采用Ф1mm,所以铜钢的送丝比例就是焊丝的送丝速度比。

焊接过程中主、辅丝分别选用铜、钢焊丝，通过调节它们的送丝速度，来改变焊缝中Fe的含量，对不同工艺参数下的焊缝外观质量进行了分析，也得出了送丝速度与焊缝中Cu和Fe的比例的关系。

借助光学显微镜和布氏硬度计等分析手段，分析了焊接接头的组织结构及不同区域Cu， Fe的含量，结果表明：焊缝组织以(α+ε)双相固溶体组织存在。也分析了焊接接头的硬度分布，结果表明：随着Cu：Fe比的下降，焊缝接头的硬度逐渐升高。68167

毕业论文关键词铜一钢异种金属双丝焊裂纹焊缝送丝速度显微组织布氏硬度

毕业设计说明书（论文）外文摘要

Title the Research on microstructures and performance of copper and steel double wire welded joints

Abstract

This article includes the T2 copper and steel Q235 twin wire welding dissimilar metals research process with silicon bronze + steel. Because the wire diameter are used Ф1mm, so the proportion of copper steel wire is wire feed speed ratio.

In the welding process,the main welding wire and auxiliary welding wire respectively choose copper,and steel wire.the content of Fe in the weld is changed by adjusting the wire feeding speed.Analyzed the weld appearance quality under different process parameters, we can concluded that the wire feeding speed is in proportion to the content of Cu and Fe in the weld.

With optical microscope，an analysis on the organizational structure of welded joints and contents of Cu and Fe in different areas is made. As shown in the results that，The weld microstructure were existed by dual phase solid solution (α+ε) organization. We also analyzed the hardness distribution of welded joint, the results showed that the Cu, Fe ratio drops, the hardness of weld joints increased.

Keywords dissimilar metal of copper and steel double-wire welding crack weld Wire feeding speed microstructure　　Brinell hardness

1 绪论 5

1．1 铜-钢异种金属焊接的发展现状 5

1.1.1 铜-钢焊接的主要特点 5

1.1.2 铜-钢异种金属焊接方法 6

1.1.2.1 熔焊 6

1.1.2.2 压焊 8

1.1.2.3 钎焊 8

1.1.2.4 熔焊-钎焊 9

1．2 双丝焊的发展现状 9

1.2.1 双丝焊的分类和设备 9

1.2.2 双丝焊的研究状况 10

1．3 本课题所需研究的问题及方案 11

2 试验设备及试验材料 12

2．1 试验设备 12

2.1.1 STARMATIC R450 TOPMAG自动双丝焊接系统 12

2.1.2 OLYMPUS (GX71)光学显微镜 13

2.1.3 HBRVU一1875型布洛维光学硬度计 14

2．2 焊接母材及焊丝铜钢双丝焊接头的组织性能研究:http://www.751com.cn/cailiao/lunwen_76605.html