菜单
  

    easier derivation [11]. In any case, the equations of motion can be expressed as  where M, C,and K are the inertia, damping, and stiffness matrices, respectively. The vector Q includes the generalized forces and q are the generalized coordinates.
    As Fig. 2 shows, in addition to the generalized coordinates from the continuous portion, there are two additional generalized coordinates, one to describe the carriage position uc(t).and another to describe the rotor angular position θm(t). Therefore, the total system order is N = NU +N,with NU =Nu +1 and N.= Nθ.+1.
    3 Modal formulation
    The solution of the eigenvalue problem [[K].ωj 2[M]]{φj}=[0] relatedtoEq. 9 gives N eigensolutions, each one featuring a natural frequency ωj and a normal mode {φj}. Applying the modal transformation {q}=[φ]{η}, the displacement field presented in Eq. 1 can be expressed as  
    To compute the axial and angular components of the mode functions, it is necessary to distinguish, in each mode vector {φj}, the elements corresponding to each
    generalized coordinate. In this sense, if the generalized coordinates vector q has the following arrangement:  each mode vector {φj}can be written as
     4 Analysis of the mode functions for different transmission ratios
    The mode functions were obtained according to Eqs. 13 and 14 in which the mode vectors correspond to the particular carriage position xc =0.5 L, and a total
    moving mass of mc =30 kg. The number of terms in the Ritz series were Nu =Nθ.=4 obtaining a suitable compromise between model complexity and estimation
    error [14]. From Eq. 6, it can be seen that the transmission ratio has a direct influence on the degree of coupling between the axial and torsional deformation fields. Therefore, two particular values of transmission ratio (screw lead) are selected for the following study.
    Figure 3 shows the axial and angular components of the mode functions for the first four modes for a transmission ratio of 10 mm/rev. Also, in Fig. 3a, the displacement of the carriage was described in each mode as a point value φuc j plotted at x =xc. Similarly, in Fig. 3b, the displacement of the motor rotor was
    described by φθm j plotted at xm =.0.2 L. Note that the zero coordinate is located at the rigid bearing; therefore, the middle of the motor is located at negative coordinate values.
    Table 2 compares the natural frequencies for the coupled and decoupled solutions for a transmission ratio of 10 mm/rev. The classification, either as torsional or axial, of the modes from the coupled model is done based on the best agreement between the frequencies of both models. The last column shows the error in the natural frequency values from decoupled system solutions; in this sense, a greater error means greater axial–torsional coupling. Similarly, Table 3 shows the results for a screw lead of 32 mm/rev.
    5 Mode frequency variation for different operating conditions
    The mode shapes and their frequencies are sensitive not only to design parameters, as was shown for different transmission ratios, but also to operation conditions,
    like carriage position and total moving mass. The results presented in the previous sections are for a carriage position of xc = 0.5 L and a total mass of mc = 30 kg. Following, the natural frequencies were studied for different carriage positions, different moving masses, and the combination of them, all for the two proposed transmission ratios. In each case, the natural frequency deviation for each mode was computed according to      In this way, the rows of Table 4 show the relative deviation of the first natural frequency for the three operation conditions, evaluated at the two transmission
    ratios. Similarly, Tables 5 and 6 show the results for the second and third vibration modes, respectively.
    According to results in Table 4, the first mode shows to be very sensitive to the carriage position for both transmission ratios. Also it is very sensitive with respect
  1. 上一篇:自主视觉云台结构设计英文文献和中文翻译
  2. 下一篇:轧钢机的英文文献及中文翻译
  1. PHP动态建模英文文献和中文翻译

  2. 波士顿托宾纪念大桥的结...

  3. 船舶设计多维问题的元建...

  4. 极限荷载近场动力学建模英文文献和中文翻译

  5. 仿真建模英文文献和中文翻译

  6. 混凝土构件中裂纹建模英文文献和中文翻译

  7. 机械臂的控制数学建模英文文献和翻译

  8. 杂拟谷盗体内共生菌沃尔...

  9. 十二层带中心支撑钢结构...

  10. 大众媒体对公共政策制定的影响

  11. 中考体育项目与体育教学合理结合的研究

  12. 河岸冲刷和泥沙淤积的监测国内外研究现状

  13. 酸性水汽提装置总汽提塔设计+CAD图纸

  14. 乳业同业并购式全产业链...

  15. 电站锅炉暖风器设计任务书

  16. 当代大学生慈善意识研究+文献综述

  17. java+mysql车辆管理系统的设计+源代码

  

About

751论文网手机版...

主页:http://www.751com.cn

关闭返回