菜单
  

    vibration. The results are given in the last two columns of Fig. 18. The second and
    third columns give the most and least favorable amplification factors from Fig. 19,
    based on knowing only the inertias of the system components. From these it appears
    that this mill is basically well designed torsionally, since test torques are not much
    greater than for the most favorable system.
        The fourth column gives the result using the Snively and Black formula based on
    knowing only the first three natural frequencies of the system.
        Test torques are as much as 28 to 51 percent higher than the column 6 calculated
    values, and this will be discussed later.
        While damping has a minor effect on peak torques resulting from suddenly
    applied torques, we at Elliott are vitally concerned with the magnitude of torsional
    damping. We occasionally encounter a system in which the natural frequencies cannot
    adjusted to avoid resonance with an operating speed. We then must be able to
    estimate the typical magnitudes of damping as well as of exciting torques that can be
    expected for the various system elements, in order to calculate factors of safety.
        The authors have considered only damping torques defined as a function of the
    difference in velocity between adjacent inertias, as indicated by their equations (2-5).
    This represents material damping in shafts, which is negligible since shaft material
    has a log decrement in the order oi 0.002, whereas the tests indicate an overall log
    decrement in this system of about 0.32. This can also represent damping due to loose
    coupling fits, which is unlikely except for the roll couplings where rapid wear of
    clearances suggests abnormally high damping. Calculations show that if all damping
    were generated by the roll couplings, their damping ratio would have to be about 0.3
    to 0.5 (Q — 1 to 1.7), which appears too high to be likely, so other or additional
    damping sources must be found.
         Material damping may also be generated in the material being rolled, which may
    be greater than for shaft material due to elevated temperature and greater plasticity.
    Slippage between work and rolls, and between work rolls and backup rolls would
    also produce damping, but the absence of chatter does not point to this source. The
    torsional model used by the writer does not permit the use or study of this source of
    damping, since infinite stiffness was assumed between rolls.
        Main test phase T max, Table 2 of 71VIBR-95, design
    arance.
     Most favorable single degree of freedom system.
     Very unfavorable system.
     From equation (7) of Snively & Black, 33 Mar. 1964 issue.
     Pollard approx. method - undamped,
     Pollard approx, method - damped.
            Branch in system neglected.
            Backlash neglected.
            Damping neglected except in last column. the steel being rolled, due to the nonuniform velocity rather than to a hysteresis loop
    in shear.
        Assuming no damping other than due to varying roll velocity, the damping
    contributed by the rolls would correspond to about Q = 7 (damping ratio = 0.072),
    which does not appear unreasonable.
        Fig. 20 shows the calculated transient torque corresponding to this value of roll
    damping plus the indicated damping assumed motors and gear. Comparison with the
    authors' test curves shows that vibration in the second critical does not attenuate as
    rapidly as in the tests, and since calculations show the second critical to be relatively
    insensitive to any but motor damping, indicates greater motor damping is present.
  1. 上一篇:建模滚珠丝杠传动英文文献和中文翻译
  2. 下一篇:排气通风系统英文文献和中文翻译
  1. 汽车乘员舱的声振耦合英文文献和中文翻译

  2. 立体光照成型的注塑模具...

  3. 数控机床英文文献和中文翻译

  4. 工业机械手英文文献和中文翻译

  5. 低频振动的铁路车轴的状...

  6. 接头的形状对沥青塞接头...

  7. 数控加工技术英文文献和中文翻译

  8. 电站锅炉暖风器设计任务书

  9. 河岸冲刷和泥沙淤积的监测国内外研究现状

  10. 酸性水汽提装置总汽提塔设计+CAD图纸

  11. 十二层带中心支撑钢结构...

  12. 杂拟谷盗体内共生菌沃尔...

  13. 中考体育项目与体育教学合理结合的研究

  14. 乳业同业并购式全产业链...

  15. java+mysql车辆管理系统的设计+源代码

  16. 当代大学生慈善意识研究+文献综述

  17. 大众媒体对公共政策制定的影响

  

About

751论文网手机版...

主页:http://www.751com.cn

关闭返回