菜单
  

        Fig. 21 shows the effect of increasing motor damping together with somewhat
    reduced roll damping. This matches the tests well enough to establish that motor
    damping corresponds to about Q = 20 and roll damping to about Q = 10.     
        Dimensionless expressions such as Q, damping ratio, and logdecrement relate
    "inertial" damping to the inertia of the systehi element involved. However, the inertia
    per se does not generate the damping, which is a power loss more logically related to
    the power being absorbed or generated by the system element involved.Consequently,
    it is unwise to assume that a test value of Q obtained for one machine is valid for a
    different design of that type of machine. For example, suppose the back-up roll
    diameter were increased such that the total idealized roll inertia were doubled. The
    work done by the rolls is the same, the power expended in damping is the same, but
    the Q of the rolls required to represent the same damping would be doubled. ;
    Consequently, a better expression than Q is needed to compare damping of, say,
    compressors of different size and design.
         It is therefore proposed that Q/H, or alternatively damping ratio multiplied by H,
    be adopted as the figure of merit for inertial torsional damping of turbines and
    compressors, where H is the ratio of the energy in HP sec stored in the inertia at test
    speed, to the HP of the machine under test conditions. For AC generators and motors
    H should be based on rated HP and speed. Our tests to date indicate that gear damping
    is independent of H, and that Q alone is a good figure of merit for gears with
    acceptable noise and lateral vibration. One test on a system with an unusually rough
    gear indicated several times the gear damping that we normally find.
        Returning to the discrepancy between calculated and maximum test torques shown
    in Fig. 18, several explanations are possible. Coupling backlash in the new unworn
    condition may be sufficient to cause this increase above the step torque calculations. It
    is also possible that the torque required as the work enters the rolls and comes up to
    full speed is that much greater than the steady rolling torque, and hence the initial step
    of torque is correspondingly greater. Another possibility is that the forcing function is
    the sum of a step of torque plus a Dirac impulse function. This possibility is explored
    in Fig. 22 where the additional sine terms represent the impulse. The impulse was
    chosen to result in about the maximum test value of peak torque and causes a phase
    shift toward zero time for both natural frequencies, and an excursion above zero
    torque for the second and fourth half cycles. Since neither of these effects is typical of
    the authors' test results, it appears that the forcing function does not contain a pure
    impulse effect of significant magnitude
        Authors' Closure
        We agree that a shock sensitive system can respond violently to the correct torque
    time input function irrespective of the initial state of clearance. We wanted to
    demonstrate the need for "off design" analysis by showing that a drive system that
    was sound dynamically when operating under design clearances exhibited large
    torsional amplification factors as the available clearances increased.
       We have found that the areas Mr. Pollard neglects can be very critical in certain
    systems, e.g., backlash has proven to be one of the most sensitive parameters relative
    to torque amplifications in rolling mill drive systems; the shock propagation can be
    quite nonsynchronous in branched systems (this was measured to be a function of bar
    entry conditions); motor torque in the system can effect torque amplification factors
  1. 上一篇:建模滚珠丝杠传动英文文献和中文翻译
  2. 下一篇:排气通风系统英文文献和中文翻译
  1. 汽车乘员舱的声振耦合英文文献和中文翻译

  2. 立体光照成型的注塑模具...

  3. 数控机床英文文献和中文翻译

  4. 工业机械手英文文献和中文翻译

  5. 低频振动的铁路车轴的状...

  6. 接头的形状对沥青塞接头...

  7. 数控加工技术英文文献和中文翻译

  8. 电站锅炉暖风器设计任务书

  9. 河岸冲刷和泥沙淤积的监测国内外研究现状

  10. 酸性水汽提装置总汽提塔设计+CAD图纸

  11. 十二层带中心支撑钢结构...

  12. 杂拟谷盗体内共生菌沃尔...

  13. 中考体育项目与体育教学合理结合的研究

  14. 乳业同业并购式全产业链...

  15. java+mysql车辆管理系统的设计+源代码

  16. 当代大学生慈善意识研究+文献综述

  17. 大众媒体对公共政策制定的影响

  

About

751论文网手机版...

主页:http://www.751com.cn

关闭返回