菜单
  

    The measurement block incorporating the system for condi-tioning four analogue signals enables the gain and offset control, so the sensors operating in the voltage range ±10 V can be easily connected to the ACS. The voltage range handled by the meas-urement block necessitates the use of a DC/DC +5 V/±15 V con-verter in the power supply block. The MSP430 has an integrated USB interface which can be utilised for programming and data exchange with the microprocessor. The current levels to be han-

     Unauthenticated

    Download Date | 3/31/16 1:19 PM 

    Maciej Rosół, Bogdan Sapiński

    Autonomous Control System for a Squeeze Mode MR Vibration Isolator in an Automotive Engine Mount

     dled by the USB interface block are limited to 100 mA and the data lines D+ and D- are surge-voltage protected.

    The CAN bus block enables the ACS communication with pe-ripheral devices via the CAN bus. This block is implemented

     on an integrated SPI/CAN converter and a CAN transceiver. The maximal data transmission throughput is 1 Mbit/s.

    Fig. 1. Block diagram of the ACS

    Tab. 1. Technical parameters of MSP430

    Parameter Description

    Program memory 128 kB

    Data memory SRAM 8+2 kB (additional 2 kB without

    I/O number Max. 63

    Number of Timers/Counters 4 Watchdog Yes

    PWM mode Yes

    Communication protocols (USCI) Channel A: UART/LIN/IrDA/SPI

    Channel B: I2C/SPI

    DMA 3 channels

    Multiply unit (MPY) 3232

    Comparator Yes

    Integrated temperaturę sensor Yes

    A/D converter 12 channels, 12-bit

    Integrated USB interface Yes

    3. TESTING

    3.1. Laboratory setup

    The schematic diagram of the laboratory set-up for ACS test-ing is shown in Fig. 2. The power interface and ACS are supplied from the battery +12 V. The monitoring and data acquisition are supported by a purpose-developed application written in the Lab-View and activated on a PC. The data transmission between the ACS and PC is effected via a sbRIO-9639 card equipped with the CAN interface (ACS connection) and the Ethernet (PC con-nection). The power interface ensures the current levels 11−12 A to be as required in the electromagnet coil.

    Fig. 2. Block diagram of the test configuration

    The application supporting the operation of measurement sensors and control of the electromagnet coil is MSP430 enabled. The primary function of this application, written in the C/C++ language in the Code Composer Studio (CCS) environment is to generate the command signal basing on the current meas-ured in the electromagnet coil, so that the current should be main-tained on the preset level. Besides, the application configures and handles the digital analogue signals from the microcontroller (including the signals from the PWM signal generator, an A/C converter and the SPI interface supporting the communication with the SPI/CAN converter). To lend the controller a deterministic feature, the control algorithm is activated in the procedure of interruption from the timer. The time interval of this interruption is set to be 1 kHz. This value was selected basing on the trans-missibility characteristics of the power interface, obtained for the VI-MR, shown in Fig. 3. The gain Mg is derived from formula (1).

  1. 上一篇:冷挤压生产过程的评价英文文献和中文翻译
  2. 下一篇:高压成形设计英文文献和中文翻译
  1. 便携式电子硫化机效率英文文献和中文翻译

  2. 主轴自振式钻头的加工预...

  3. 沥青填充式伸缩缝英文文献和中文翻译

  4. 平行和分布式作业破碎机英文文献和中文翻译

  5. 双曲柄环板式针摆线齿轮...

  6. 质量有缺陷的滚动轴承振...

  7. 冷挤压变形特性英文文献和中文翻译

  8. 电站锅炉暖风器设计任务书

  9. 河岸冲刷和泥沙淤积的监测国内外研究现状

  10. 乳业同业并购式全产业链...

  11. java+mysql车辆管理系统的设计+源代码

  12. 当代大学生慈善意识研究+文献综述

  13. 大众媒体对公共政策制定的影响

  14. 中考体育项目与体育教学合理结合的研究

  15. 酸性水汽提装置总汽提塔设计+CAD图纸

  16. 十二层带中心支撑钢结构...

  17. 杂拟谷盗体内共生菌沃尔...

  

About

751论文网手机版...

主页:http://www.751com.cn

关闭返回