菜单
  

    • All extremities should fill at the same pressure.
    Designers may also have some specific quality requirements,
    such as minimising the maximum shear stress, uniform end-
    of-fill temperature, uniform volumetric shrinkage, and uniform
    warpage. Some requirements may be imposed on a particular
    location or area of the plastic part, such as the shear stress re-
    quirement at the vicinity of snap fits and screw holes.
    To enable the designers to specify these criteria rather than
    hard-wire them in a computer program, we modify the part fea-
    ture by replacing the existing constraint attribute with two cri-
    teria attributes: a verification criteria attribute and an evaluation
    criteria attribute. Each of these attributes contains a list of crite-
    ria. The verification criteria refer to those that must be satisfied,
    such as the first three criteria listed above; while the evaluation
    criteria refer to those that should be minimised, such as the last
    three criteria listed above. Case-specific requirements may also
    be classified as either verification criteria or evaluation criteria.
    Part feature is further extended to include a new attribute for
    storing a list of variables from which the verification and evalua-
    tion criteria can be constructed. These variables are thus referred
    to as criteria construction variables. The following is a list of
    some of these variables (the units are put inside the brackets,
    where “SD” stands for standard deviation):
    • v1 = maximum shear stress (MPa);
    • v2 = maximum shear rate (1/s);
    • v3 = maximum pressure (MPa);
    • v4 = maximum flow front temperature (
    ◦C);
    • v5 = minimum flow front temperature (
    ◦C);
    • v6 = maximum end-of-fill temperature (
    ◦C);
    • v7 = minimum end-of-fill temperature (
    ◦C);
    • v8 = maximum cooling time (s);
    • v9 = minimum cooling time (s);
    • v10 = actual injection time (s);
    • v11 = maximum volumetric shrinkage (%);
    • v12 = minimum volumetric shrinkage (%);
    • v13 = maximum clamp tonnage (tonnes);
    • v14 = uniform end-of-fill temperature (SD);
    • v15 = uniform cooling time (SD);
    • v16 = uniform volumetric shrinkage (SD);
    • v17 = uniform warpage (SD);
    • v18 = uniform filling time at extremities (SD);
    • v19 = uniform pressure at extremities (SD);
    The new attribute stores a list of criteria-construction vari-
    ables selected by the designers from these commonly used vari-
    ables. Each selected variable may itself be used as an evaluation
    criterion, such as “v1 = maximum shear stress” and “v15 = uni-
    form end-of-fill temperature;” or it may be used to construct
    a criterion with or without other variables; for example, the vari-
    able “v1 = maximum shear stress” may be used to construct
    a verification criterion:
    v1 < 0.25MPa,
    which corresponds to an example of the first item of the list of
    requirements mentioned in the beginning of this section, where
    the maximum recommended shear stress for the material type is
    0.25MPa. Another example, corresponding to the fourth item in
    the list, is that “cooling time should be uniform and minimised.”
    If the designers select the variables “v8 = maximum cooling
    time” and “v9 = minimum cooling time,” then an evaluation cri-
    terion may be constructed as:
    minimising (v8−v9),
    which represents the intention of achieving a uniform cooling
    time (note that this may be more precisely represented by “v15 =
    uniform cooling time”).499
    When more than one evaluation criterion is constructed,
  1. 上一篇:针盖的注塑模具分析英文文献和翻译
  2. 下一篇:加强钢筋混凝土箱梁抗扭英文文献和翻译
  1. 塑料制品的注塑模具设计...

  2. 塑料注射模具设计U型铣槽...

  3. 塑料制品模具设计英文文献和中文翻译

  4. 塑料成型生产过程中形成...

  5. 薄壁注塑成型翘曲英文文献和中文翻译

  6. 塑料模具注射成型英文文献和中文翻译

  7. 齿轮机械零部件英文文献和中文翻译

  8. 酸性水汽提装置总汽提塔设计+CAD图纸

  9. 杂拟谷盗体内共生菌沃尔...

  10. java+mysql车辆管理系统的设计+源代码

  11. 乳业同业并购式全产业链...

  12. 中考体育项目与体育教学合理结合的研究

  13. 电站锅炉暖风器设计任务书

  14. 大众媒体对公共政策制定的影响

  15. 当代大学生慈善意识研究+文献综述

  16. 河岸冲刷和泥沙淤积的监测国内外研究现状

  17. 十二层带中心支撑钢结构...

  

About

751论文网手机版...

主页:http://www.751com.cn

关闭返回