菜单
  
    摘要本设计中通过对XX县城110kV降压变电站的近期负荷和远期负荷的分析,列出了约束条件,分析计算确定了变电所的主变压器以及所用变压器的型号与数量。根据国家变电站设计规范手册条例规定,分别拟定了高低压侧主接线方案,并通过比较各方案优缺点结合该变电所的实际情况,最后确定该所的电气主接线形式。将送电网络进行合理简化,画出其等效电路图并依次分析选定短路点位置,计算各线路阻抗和元件的标幺值,进而计算三相短路电流和短路容量。通过规范手册规定以及前期短路计算所得数据条件,分别对高低压侧一次电气设备进行选型拟定,并通过校验各元件的动稳定,热稳定和其他限制约束来最终确定型号。根据规范以及习惯来确定高低压侧母线材料和类型,通过具体参数的选择校验,确定母线的型号。依据《3~110kV高压配电装置设计规范》来确定高低压的配电装置形式,初步进行配电装置的布置。最后按照设计,绘制出变电所的电气主接线图,以及变电所的平面布置图。
    关键词  变电所  110kV  设计  接线  一次设备  短路计算     
    毕业论文设计说明书外文摘要
    Title    A 110kV buck substation design of XX county         
    Abstract
    In this design,Through the analysis of the substation’s  load to identified the main transformer substation and the transformer substation’s  transformer number and model.According to "35 ~ 110kV substation design specifications" Manual of regulations were drawn up high and low side once part of the main electric connection schemes, and the advantages and disadvantages of the actual situation of the substation by comparing the plan to finalize the Institute of Electrical Main connection form.Calculated data conditions specified by the rule book and previous short circuit, respectively, high and low side prepared a selection of electrical equipment, and by checking its dynamic stability, thermal stability and other restrictions to determine the device type. According to norms and habits to determine the high and low side of the bus and the type of material, by choosing specific calibration parameters determine the bus models. According to "3 ~ 110kV high voltage electrical installations" to determine the form of high and low voltage power distribution equipment, initially laid out power distribution unit. Finally, according to the design drawing substation main electrical wiring diagrams, and floor plan substation.
    Keywords  Substation  110kV  Design  Wiring   Primary equipment   Short circuit calculation 
    目   录
    1  引言    1
    2  任务说明及分析    2
    2.1  变电站原始资料    2
    2.2  设计内容及成果    3
    3  负荷分析计算及变压器的选择    4
    3.1  负荷分析计算    4
    3.2  主变压器的选择    4
    3.3  所用变压器的选择    6
    4  电气主接线的设计    8
    4.1  变电站电气主接线的要求    8
    4.2  主接线的方案拟定与选择    8
    5  短路电流计算    11
    5.1  短路电流计算条件    11
    5.2  短路计算过程    12
    6  电气设备的选择    15
    6.1  电气设备选择的原则    15
    6.2  110kV侧电气设备的选择    15
    6.3  10kV侧电气设备的选择    17
    6.4  母线的选择    20
  1. 上一篇:有源电力滤波器中交流侧纹波电流的抑制
  2. 下一篇:车载移动式警务抓拍系统设计
  1. 110kV变电站电气设计二次系统设计+电路图

  2. 110kV变电站电气设计一次系统设计

  3. 铁合金企业110KV总降压变电所设计+图纸

  4. 大学110kV智能变电站实施方案设计

  5. 110kV变电站电气设计高电压防护系统设计

  6. 电机修造厂总降压变电所...

  7. 某冶金机械厂总降压变电...

  8. 当代大学生慈善意识研究+文献综述

  9. java+mysql车辆管理系统的设计+源代码

  10. 十二层带中心支撑钢结构...

  11. 乳业同业并购式全产业链...

  12. 酸性水汽提装置总汽提塔设计+CAD图纸

  13. 大众媒体对公共政策制定的影响

  14. 电站锅炉暖风器设计任务书

  15. 中考体育项目与体育教学合理结合的研究

  16. 河岸冲刷和泥沙淤积的监测国内外研究现状

  17. 杂拟谷盗体内共生菌沃尔...

  

About

751论文网手机版...

主页:http://www.751com.cn

关闭返回