菜单
  

    and the analysis of the results more complicated.
    Most design analyses do not require detailed systemmodeling and
    simulation as the energy consumption can be estimated by using
    simpler modeling approaches. The conceptual system representation
    shows its advantages (lower required user expertise, lesser input
    data, less intense computations, easier results analysis, etc.) when
    only load predictions are considered, and/or when energy savingoptions are investigated. However, for comparing HVAC system alter-
    natives and evaluating different control strategies [18,51] detailed
    HVAC system models are required. In the system-based modeling
    approach, the speed of system alternatives evaluation is much higher
    than in the component based modeling approach, but the investiga-
    tion of innovative technologies is limited.
    Matching the applicabilities of system modeling approaches with
    the design questions at hand, the user can benefit from both ease o
    the former categories and flexibility of the latter ones. However
    building a right model for a simulation task at hand is still more an art
    than an engineering discipline. This issue is highly relevant when
    there is no (measured) data which can be used for direct mode
    accuracy evaluation. Thus, in this case the model adequacy for the
    particular simulation objective needs to be evaluated differently.
    Building a right system model for a specific purpose is to require
    that the modeling validity and data validity match as far as possible
    the required validity [52]. The required validity is assessed only
    against those aspects of the real world that are of relevance for
    successful accomplishment of simulation objectives, represented by
    performance parameters.
    Model complexity can be expressed in terms of scope (defined by a
    number of components in the model) and resolution (defined by a
    number of states per component in the model) of the model and
    interactions among components in themodel. Abstraction is a genera
    process and includes various simplification approaches with regards
    to system boundaries considered, number of modeled physica
    phenomena, the resolution of modeling of each considered phenom-
    enon, etc. in increase in model complexity increases the cost of using
    the model. Thus, the model should be of the lowest complexity while
    preserving its validity for the intended simulation objectives. The
    required lowest model complexity depends on the simulation
    objective. Also, increasing the complexity, for different simulation
    objectives, has different implications for the value of the model to the
    user, as schematically shown in Fig. 1. For different simulation
    objectives the model cost exceeds the model value to the user at
    different model complexities. For some objectives the cost of the
    model will exceed its value even when the modeling complexity is
    low, and for some, the simulation objective can justify the use ofmore
    complex models. Moreover, the rate of change in the model value can
    be different for different simulation objectives at different complex-
    ities. On the one hand, a simple model can have a high value at low
    modeling complexity for some simulation objectives; this valuemight
    not be increased by increasing the complexity. On the other hand, amodel has a value only above certain modeling complexity for some
    other simulation objectives, as illustrated in Fig. 1.
    The potential techniques that can be used to ease selection of
    modeling complexity for a particular simulation objective can be
    described in following paragraphs (the use of the techniques has been
    reported previously [53,54]).
    Definition of the minimum required modeling complexity can be
    accomplished by using the checklist rationale from [55] represented
  1. 上一篇:五轴端铣英文文献和中文翻译
  2. 下一篇:数字式EL定位器英文文献和中文翻译
  1. 中央空调系统英文文献和中文翻译

  2. 通风空调(暖通空调)风...

  3. 利用地板下的空气提高建...

  4. S7-200自动化系统英文文献和中文翻译

  5. 级进模自动化结构设计系...

  6. 建筑暖通空调系统英文文献和中文翻译

  7. 自动化级进模钣金排样英文文献和中文翻译

  8. 中考体育项目与体育教学合理结合的研究

  9. 乳业同业并购式全产业链...

  10. 电站锅炉暖风器设计任务书

  11. 杂拟谷盗体内共生菌沃尔...

  12. 酸性水汽提装置总汽提塔设计+CAD图纸

  13. 当代大学生慈善意识研究+文献综述

  14. java+mysql车辆管理系统的设计+源代码

  15. 大众媒体对公共政策制定的影响

  16. 河岸冲刷和泥沙淤积的监测国内外研究现状

  17. 十二层带中心支撑钢结构...

  

About

751论文网手机版...

主页:http://www.751com.cn

关闭返回